EDMI GS-60B Installation And Commissioning Manual

EDMI GS-60B Installation And Commissioning Manual

Residential gas meter
Hide thumbs Also See for GS-60B:

Advertisement

Quick Links

GS-60B Residential Gas Meter
Installation and Commissioning Guide
Date: 22/01/2019
Version / Status: 0.9

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GS-60B and is the answer not in the manual?

Questions and answers

Summary of Contents for EDMI GS-60B

  • Page 1 GS-60B Residential Gas Meter Installation and Commissioning Guide Date: 22/01/2019 Version / Status: 0.9...
  • Page 2: Confidentiality

    Commissioning Guide Confidentiality The information that is contained in this document is the exclusive property of EDMI Europe Limited (“EDMI”) except as otherwise indicated. The contents of this document and any attached appendices, in whole or in part, must not be reproduced, stored, transmitted or used for design purposes without the prior written permission of EDMI Europe Limited.
  • Page 3: Table Of Contents

    Revision History ........................17 Contact Us ..........................17 List of Figures Figure 1-1 Front view of GS-60B..................... 4 Figure 1-2 Side view of GS-60B ...................... 4 Figure 1-3 View of internal battery compartment ................4 Figure 4-1 Location of the pushbuttons................... 8 Figure 4-2: Gas Flow Direction ......................
  • Page 4: Introduction

    Figure 1-3 View of internal battery compartment Figure 1-2 Side view of GS-60B The GS-60B is a UK SMETS compliant battery powered ultrasonic gas meter with smart functionality and wireless communications. Gas flow rate is calculated using a single bounce speed of sound measurement through a patented ultrasonic measurement technique.
  • Page 5: Guidance For Initial Delivery

    Authorisation for return is required for all products shipped to the factory for repair, calibration, warranty, exchange or credit. To obtain authorisation, an RMA number for return of GS-60B gas meters must be issued, which can be obtained from your meter supplier. All returns should be packaged in the original boxes and pallet structure if available, in order to ensure that the product has the sufficient protection during transit.
  • Page 6: Storage And Initial Handling

    Only suitably trained and qualified personnel shall be allowed to install the meter. Local safety standards shall be observed and shall take precedence over this guidance. The GS-60B is fitted with British Standard size and spacing of bosses to replace existing gas meters.
  • Page 7: Push Button Operation

    Push Button Operation The GS-60B has two pushbuttons on the front of the meter, allowing installers and end users to interact with the meter. Figure 4-1 shows the positioning and format of the left (Hold to back) and right (Hold to OK).
  • Page 8: Physical Install With Safety Checks

    The physical install of the meter is a standard procedure, which properly trained gas safe engineers shall perform. The GS-60B provides standard fittings and test point to ensure a safe install.
  • Page 9: Commissioning

    If the Communications Hub indicates that the HAN has been successfully formed and that it is in a state to allow joining, press the OK button. Copyright © 2019 EDMI Europe Ltd. All rights reserved Version / Status: 0.9 PAGE 9 OF 17...
  • Page 10 Please note: The exact DUIS request numbers may vary between suppliers – the numbers below are simply for illustrative purposes only Message+ Description GSME has finished pairing and is waiting to receive its first GBCS message. Copyright © 2019 EDMI Europe Ltd. All rights reserved Version / Status: 0.9 PAGE 10 OF 17 Public...
  • Page 11 ‘OK’ button to dismiss the commissioning screen Press OK to dismiss the message and return to normal operational mode. Copyright © 2019 EDMI Europe Ltd. All rights reserved Version / Status: 0.9 PAGE 11 OF 17 Public...
  • Page 12: Normal Meter Operation

    Home Area Network. One of the most common problems that may encounter is that of the meter not being on the Communications Hub whitelist. Refer to your company’s installation procedures regarding whitelisting. Copyright © 2019 EDMI Europe Ltd. All rights reserved Version / Status: 0.9 PAGE 12 OF 17...
  • Page 13 Attempt to join the HAN again – if the key establishment. the error persists please contact Copyright © 2019 EDMI Europe Ltd. All rights reserved Version / Status: 0.9 PAGE 13 OF 17 Public...
  • Page 14 HAN. ¯¯ ¯¯ ¯¯ ¯¯ ¯¯ ¯¯ ¯¯ ¯¯ ¯¯ ¯¯ ¯¯ ¯¯ LCD rather than ‘Press OK to join HAN’. Copyright © 2019 EDMI Europe Ltd. All rights reserved Version / Status: 0.9 PAGE 14 OF 17 Public...
  • Page 15: User Interface Display Of Meter Status

    There is also a priority order to the meter status flag display, whereby a higher priority pre- empts a lower priority. Where 1 is the highest priority. Copyright © 2019 EDMI Europe Ltd. All rights reserved Version / Status: 0.9...
  • Page 16: Glossary Of Terms

    DCC User Interface Specification – DCC Service user reference document DUIS Great Britain Technical Specification – Technical specification document, a compliment to SMETS GBCS GSME Gas Smart Metering Equipment Copyright © 2019 EDMI Europe Ltd. All rights reserved Version / Status: 0.9 PAGE 16 OF 17 Public...
  • Page 17: Revision History

    23/01/2018 Added new section: “8 User Interface Display of Meter Status” 12/03/2018 Additional information added following review 14/03/2018 Section 4.3 updated and images of GS-60B added to document 10/04/2018 Updated as per customer feedback. 22/01/2019 Approved via Email Contact Us If you have any further questions or would like to get in touch, please use the details below.

Table of Contents

Save PDF