Advertisement
Quick Links
Advertisement
Related Manuals for SB Acoustics Ara
Summary of Contents for SB Acoustics Ara
- Page 1 Ara / Ara-Be Kit User Manual REV.1 (03.09.2018)
- Page 2 Manual | Ara / Ara-Be Kit Technical specication : Ara-Be Frequency range 45-25000 Hz +/-3 dB 45-30000 Hz +/-3 dB Sensitivity (2.83V / 1m) 87 dB 87 dB Nominal impedance 4Ω 4Ω Max SPL 105 dB 105 dB Recommended amplier :...
- Page 3 Manual | Ara / Ara-Be Kit Frequency response (Ara-Be) 20kHz Frequency response (Ara) 20kHz Response Curve : ------ (Blue) : on axis ------ ( Green ) : 15° off-axis ------ ( Red ) : 30° off-axis Measured on-axis, 15° and 30° off-axis at 1 m in an ordinary room. Lower frequency dips and peaks are caused by room modes/reections.
- Page 4 Manual | Ara / Ara-Be Kit Mechanical drawing (size in mm)
- Page 5 Manual | Ara / Ara-Be Kit...
- Page 6 Manual | Ara / Ara-Be Kit SATORI TW29R or TW29BN (Sold separately)
- Page 7 Manual | Ara / Ara-Be Kit...
- Page 8 Manual | Ara / Ara-Be Kit Damping material position (size in mm)
- Page 9 Manual | Ara / Ara-Be Kit Crossover Schematic Ara-Be Crossover Schematic Ara Black ! Reversed polarity 1.5ohm/10W 2.7ohm/10W Black Yellow 5.6uF/400V 0.2mH/0.7mm 1.1mH/0.5mm TW29R(B) 3.3ohm/10W 2.7ohm/10W 62uF/100V 1.2mH/1.4mm 0.6mH/1.4mm Black MW16P-4 4.7uF/400V 6.8ohm/10W...
- Page 10 High frequency driver Satori TW29R or TW29BN (sold separately) ... 1 pc - Low frequency drivers 6½" Satori MW16P-4 (sold separately) ..1 pc - Ara kit crossover (sold separately) ............12 pcs - Hex socket screw M4 x 20mm (for drivers) ........4 pcs - Countersunk screw M4 x 20mm (for terminal plate) ......
- Page 11 Manual | Ara / Ara-Be Kit 1. Take out the cabinet from the packaging and take out the raw damping material from the cabinet 2. Cut the raw damping material to 7 pcs of damping according to the cutting pattern diagram 3.
- Page 12 Manual | Ara / Ara-Be Kit 4. Fasten the crossover by tightening all 6 screws 5. Pass the input wire through hole in the rear panel of the cabinet 6. Seal the cable hole with hot melt glue...
- Page 13 Manual | Ara / Ara-Be Kit 7. Pull the tweeter cable through the hole in cabinet bracing 8. Place each damping part into the cabinet according to position diagram. Add a bit of glue if needed to hold the damping in place 9.
- Page 14 Manual | Ara / Ara-Be Kit 10. Mount the terminal panel into the terminal hole at the back side 11. Hook up the cable to the tweeter and woofer terminal...
- Page 15 Manual | Ara / Ara-Be Kit 1 2 . M o u n t t h e d r i v e r t o the cabinet and fasten the screws...
Need help?
Do you have a question about the Ara and is the answer not in the manual?
Questions and answers