Related Manuals for VIVID STORM S PRO PLUS
Summary of Contents for VIVID STORM S PRO PLUS
- Page 1 S PRO PLUS Electric Tab-Tension Floor Screen USER MANUAL (2402) (S PRO PLUS & S PRO P PLUS common version)
-
Page 2: Table Of Contents
Content To Users ---------------------------------------------------2 Screen Running ----------------------------------------19 Manual Switch ----------------------------------------19 Safety Instructions -------------------------------------2 Remote control ---------------------------------------20 Packing Contact-----------------------------------------4 Adjustment Of Screen Black Borders -------------22 The Introduction Of Product --------------------------5 Screen Maintenance ----------------------------------23 Appearance ---------------------------------------------5 Manufacturer's Warranty ----------------------------24 Certificate ------------------------------------------------8 Certificate -----------------------------------------------26 Important Safety Precautions -----------------------9 Product Warranty Card -------------------------------26 Matters Needing Attention -------------------------10... -
Page 3: To Users
To Users Thank you for choosing the VIVIDSTORM projection screen. Please read this manual carefully before using the product and keep it properly. The manual of products, accessories, user interface, etc. in this description are schematic diagrams and are for reference only. Due to product updates, the actual product may be slightly different from the schematic diagram, please refer to the actual product. - Page 4 To prevent electric shock, fire hazard. - Using incorrect cables may affect product performance, and may even lead to electric shock, fire and other accidents. In order to ensure product performance and safety, please use the same type of cable as the original cable. - If a power extension cord is required, use a power cord with an amperage rating not lower than that of the product.
-
Page 5: Packing Contact
When opening the box, check the contents of the box the list below. If there is any omission, please contact the dealer in time. S PRO PLUS Electric Tab-Tension Floor Screen USER MANUAL (2402) (S PRO PLUS & S PRO P PLUS common version) Projection screen User manual+Envelopes RF wireless remote Power cord... -
Page 6: The Introduction Of Product
The Introduction Of Product Inside the dotted line is Appearance the standard projected area Outside the dotted (the actual product line is the non-projected does not have this dotted line) Upper Cover Support bar Tab-Tension Screen material Bottom Black border Housing Power cord (Screen open - front view) - Page 7 Appearance Upper Cover (Screen close - front view) Rotatable bracket Housing Support bar Screen material (Screen close - back view) Rotatable bracket Housing Screen manual switch Screws Housing Power cord socket Power Switch (Screen open - left view) (Screen open- right view) (Screen close - front view) (Screen close - back view) Rotatable bracket...
- Page 8 Appearance Upper cover Screen material Screen Black border Housing Power cord socket Power Switch Screen manual switch Do not touch Schematic diagram of left end cover the screen material...
-
Page 9: Certificate
Pilot lamp Screen manual switch Power lamp, make the following prompts Power cord socket for the working status: - In the left picture (picture 1), make sure that the power cord plug is inserted into the product socket. After turning on the red power switch, the red light is on to indicate the power-on state;... -
Page 10: Important Safety Precautions
Important Safety Precautions Please read all the contents of the user guide carefully and follow the operation steps below. For reference when necessary, please keep this user guide. 1. In order to avoid damage to the equipment, please prohibit the use of any accessories not authorized by the manufacturer. 2. -
Page 11: Matters Needing Attention
Matters Needing Attention No one is allowed to open the inside of the equipment and repair the product without authorization, except for the authorized technicians. 1. Please make sure that the power supply connected to this product has stable current. 2. -
Page 12: Matters Concerning Projection
Matters Concerning Projection Projected Area 1.Please project according to the actual projection size of the screen purchased when using the projector. 2.Since the position of black border has been preset on the screen of this product, please do not exceed the specified projected area during projection. -
Page 13: Screen And Projector Compatibility
Screen and projector compatibility Please note that the screen of this product is only suitable for use with Ultra short throw laser projector. If it is used with other projector ，the effect of picture will be greatly reduced. Ambient light can be absorbed It is suggested that the ultra short focus laser projector throw ratio should be ≤... -
Page 14: About Screen Performance
About Screen Performance 1.Please note that when placing this product, please make sure that the product is always in a horizontal state. Do not place the screen in an inclined or vertical position. 2. After using for a period of time, if the cover on both ends of the screen is slightly tilted, there is no need to worry. This is a normal phenomenon and does not affect the viewing and use. - Page 15 4.When there are a few black spots, white spots, stains and other impurities on the screen surface, but if they are qualified according to the detection method, then such situation is not a product quality problem, and it is within the scope of product qualification.
- Page 16 For the black spot defect which can be For the appearance of specific measured in appearance, if it can not be measurable white spot defects, if visual found by visual inspection, the product is inspection can not be found, then the normal.
-
Page 17: Installation Warning
Installation Warning Since the installation environment of each user is different, the instructions in this user guide are only for reference. If you need further installation and safety suggestions, please consult the professional installation company. It should be noted that no matter what kind of installation method you take, the product should not be loosened or dropped due to vibration or tension, so as to keep the product stable. -
Page 18: Ground Installation
Ground Installation Safety tips: it is recommended that two people lift the product and place it horizontally. 1. When using this product, you can place the product on the horizontal ground and fix it. Before placing the product, please pay attention to cleaning the ground debris to keep the floor dry. -
Page 19: Wall Installation
Wall Installation (The wall hanger can be used as a reference If additional purchase it) 1. If you purchase the wall brackets, you can fix the product screen on the wall. 2. When installing the product, first you need to make a horizontal mark on the wall and mark the hole position, and then fix the wall brackets on the wall. -
Page 20: Screen Running
Screen Running Voltage information: make sure your screen is working at the correct voltage, depending on the area. (1) Plug the screen power cord into the correct power outlet. (2) When the product power is turned on, a "beep" sound will be emitted for 1.5 seconds, indicating that the product has been powered on. -
Page 21: Remote Control
2.Remote control Function key Stop Down Screw hole positions Front of remote control Back of the remote control For convenient access, the remote controller can be fixed on the wall surface and other planes through the bracket.(wall screw or double-sided adhesive tape can be used for fixation) inside the wall outside of a wall... - Page 22 When the battery of the remote control needs to be replaced, as shown in the figure below, unscrew the cover of the remote control with a small screw, then replace the new button battery, close the cover of the remote control, and tighten the screw to prevent the loose battery from falling off;...
-
Page 23: Adjustment Of Screen Black Borders
Adjustment Of Screen Black Borders (Screen Hight Limit Setting) One Time Four Times Please ensure that the device is powered on. Begin the adjustment Enter adjustment mode: Use a pointed tool to press the 'Function’ key on after fully opening the screen. the back of the remote control 4 times, then within 10 seconds, press the 'Up' key on the remote control 1 time. -
Page 24: Screen Maintenance
Screen Maintenance Cleaning requirements: 1. In general, please use a soft brush to clean the screen surface. Remember to use a special soft brush and gently brush away the impurities along the screen grain direction. 2. Do not use any cloth (coarse cloth, soft cloth, gauze, wet cloth) to wipe the screen surface. 3. -
Page 25: Manufacturer's Warranty
Manufacturer's Warranty Thank you for choosing VIVIDSTORM screens for your home or business. We are committed to providing high-quality products that meet your expectations. To ensure your satisfaction and peace of mind, we offer the following warranty policy for VIVIDSTORM screens: 1. - Page 26 8. Limitation of Liability: VIVIDSTORM'S liability under this warranty is limited to the repair or replacement of the defective screen or its components as stated above. VIVIDSTORM shall not be liable for any indirect, consequential, or incidental damages arising from the use or inability to use the screen.
-
Page 27: Certificate
Certificate Product Name: Product Model No: Factory serial No： Inspector: Date of production： The product has been tested and inspected after operation，and all the tests and inspections have been in accordance with the technical requirements，and its quality meets the specified requirements.Only after passing the inspection can they be allowed to leave the factory.
Need help?
Do you have a question about the S PRO PLUS and is the answer not in the manual?
Questions and answers