VIVID STORM PHANTOM Recessed In-Ceiling Motorized Tension UST ALR User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

PHANTOM Recessed In-Ceiling Motorized

Tension UST ALR Projector Screen

USER MANUAL

Table of Contents

Need help?

Do you have a question about the PHANTOM Recessed In-Ceiling Motorized Tension UST ALR and is the answer not in the manual?

Questions and answers

Summary of Contents for VIVID STORM PHANTOM Recessed In-Ceiling Motorized Tension UST ALR

Page 1 PHANTOM Recessed In-Ceiling Motorized Tension UST ALR Projector Screen USER MANUAL...
Page 2: Table Of Contents
Content To Users ---------------------------------------------------2 Screen Running ----------------------------------------30 Remote Control ---------------------------------------31 Safety Instructions -------------------------------------2 Screen Height Limit Setting -------------------------34 Packing Contact-----------------------------------------4 Black border up ----34 (adjust shorter the ﬁxed height of the screen) The Introduction Of Product --------------------------5 Black border down (adjust longer the ﬁxed height of the screen) Appearance ---------------------------------------------5 Screen Maintenance ----------------------------------38...
Page 3: To Users
To Users Thank you for choosing the VIVIDSTORM projection screen. Please read this manual carefully before using the product and keep it properly. The manual of products, accessories, user interface, etc. in this description are schematic diagrams and are for reference only. Due to product updates, the actual product may be slightly different from the schematic diagram, please refer to the actual product.
Page 4 To prevent electric shock, ﬁre hazard. - Using incorrect cables may affect product performance, and may even lead to electric shock, ﬁre and other accidents. In order to ensure product performance and safety, please use the same type of cable as the original cable. - If a power extension cord is required, use a power cord with an amperage rating not lower than that of the product.
Page 5: Packing Contact
Packing Contact When opening the box, check the contents of the box the list below. If there is any omission, please contact the dealer in time. PHANTOM Recessed In-Ceiling Motorized Tension UST ALR Projector Screen USER MANUAL Projection screen User manual+Envelopes Nuts for M10 End Covers Installation Bracket...
Page 6: The Introduction Of Product
The Introduction Of Product Appearance Inside the dotted line is the standard projected area Outside the dotted line is the non-projected (the actual product Threaded Rod does not have this dotted line) Housing Power cord End Covers Upper Black border Tab-Tension Screen material Lower axis...
Page 7 Appearance Screws Power cord hole Housing (Screen close - front view) Housing End Covers Screen material (Screen close - back view) Housing Lower axis (Screen open - left view) (Screen open- right view) (After the screen is closed - (After the screen is closed - internal internal anatomy left view) anatomical view from the right)
Page 8 Appearance Housing Screen Black border Screen material End Covers Lower axis Do not touch the screen material...
Page 9 Because the installation method of ultra-short throw laser projector (laser TV) is divided into hoisting or placing on the desktop, the special anti-light direction structure of the screen material surface will be changed due to the installation method of the projector; so we subdivide this product into PRO/ PRO A ;...
Page 10: Certificate
Pilot lamp Power lamp, make the following prompts for the working status: - Picture 1, when the red light of the power light is on and there is a beep~, it means it is working normally. If the red light ﬂashes and doesn‘t light up, it is abnormal, please contact after-sales support.
Page 11: Important Safety Precautions
Important Safety Precautions Please read all the contents of the user guide carefully and follow the operation steps below. For reference when necessary, please keep this user guide. 1. In order to avoid damage to the equipment, please prohibit the use of any accessories not authorized by the manufacturer. 2.
Page 12: Matters Needing Attention
Matters Needing Attention Warning! If you do not strictly follow the prescribed precautions during use, this may lead to equipment damage and other unnecessary damage. Please observe the family ﬁre safety regulations; do not place the equipment near the ﬁreplace or high temperature objects such as gas stove, barbecue or heater to avoid equipment damage.
Page 13 Matters Needing Attention No one is allowed to open the inside of the equipment and repair the product without authorization, except for the authorized technicians. 1. Please make sure that the power supply connected to this product has stable current. 2.
Page 14: Matters Concerning Projection
Matters Concerning Projection Projected Area 1.Please project according to the actual projection size of the screen purchased when using the projector. 2.Since the position of black border has been preset on the screen of this product, please do not exceed the speciﬁed projected area during projection.
Page 15: Screen And Projector Compatibility
Screen and projector compatibility Please note that the screen of this product is only suitable for use with Ultra short throw laser projector. If it is used with other projector ，the effect of picture will be greatly reduced. It is suggested that the ultra short focus laser projector throw ratio should be ≤ 0.4. (please consult the projection manufacturer for speciﬁc parameters) Ambient light can be absorbed The projection content...
Page 16: About Screen Performance
About Screen Performance 1.Please note that when placing this product, please make sure that the product is always in a horizontal state. Do not place the screen in an inclined or vertical position. 2. If there are regular creases on the screen surface after the screen is opened, don't worry. This is a normal phenomenon. It is caused by the screen being curled and tightened for a long time, which does not affect the user's viewing.
Page 17 3.When there are a few black spots, white spots, stains and other impurities on the screen surface, but if they are qualiﬁed according to the detection method, then such situation is not a product quality problem, and it is within the scope of product qualiﬁcation.
Page 18 For the black spot defect which can be For the appearance of speciﬁc measured in appearance, if it can not be measurable white spot defects, if visual found by visual inspection, the product is inspection can not be found, then the normal.
Page 19: Installation Warning
Installation Warning Since the installation environment of each user is different, the instructions in this user guide are only for reference. If you need further installation and safety suggestions, please consult the professional installation company. It should be noted that no matter what kind of installation method you take, the product should not be loosened or dropped due to vibration or tension, so as to keep the product stable.
Page 20: Installation Steps
Installation Steps Please make sure the ﬁxing surface can support the weight of the screen before installation. Make sure that all screws are tightened after the installation is complete. Please choose a suitable screen installation method 1、Using a screen bracket mounted on the ceiling (Pages 20-23) Socket Roof wall...
Page 21 Bracket mounted on the ceiling 1、 First measure the length of the product shell "L1" (including the iron end covers on both sides, please refer to the product size mark in Figure 1 for details); (Picture 1) 2、Make a slot on the ceiling at the designated installation location; slot size: (L1+74mm)*110mm*depth 103mm; and ensure that the socket in the slot is on the left.
Page 22 3、After slotting, measure or calculate the distance L2 (or L1-35mm) installed on the screen housing, and then mark the ﬁxed position L2 of the screen housing on the roof. The distance between two holes is 40mm (The distance between the two holes can be measured ﬁrst, as shown in the ﬁgure below) Distance...
Page 23 5、Pass the main body of the product through the lower side of the slotted hole in the ceiling, and use nuts to hoist it on the expansion screws. This step requires at least two people to cooperate. ① Roof ② Ceiling ①...
Page 24 6、Insert the power plug into the socket, as shown in Figure 1. Install the decorative plate on the left and right end covers. 插座 (Picture 1) Note: Do not push and pull the decorative panel up and down, as it may cause the buckle of the decorative panel to break. Socket Roof wall...
Page 25 Using the threaded rod mounted 1、First measure the length of the product shell "L1" (including the iron end covers on both sides, please refer to the product size mark in Figure 1 for details); (Picture 1) 2、Make a slot on the ceiling at the designated installation location; slot size: (L1+74mm)*110mm*reserved depth 500/1000+103mm, or ensure that the depth of the slot exceeds 103mm (the product has a conﬁguration of 500/1000mm screw, can be cut to any length);...
Page 26 3、After slotting, measure or calculate the distance L2 (or L1-35mm) installed on the screen housing, and then mark the ﬁxed position L2 of the screen housing on the roof. The distance between two holes is 95mm (The distance between the two holes can be measured ﬁrst, as shown in the ﬁgure below) Distance...
Page 27 4、According to the marked ﬁxed position, ﬁx the screw mounting bracket and the screw on the solid ceiling with screws; the length of the screw can be appropriately cut according to the actual distance from the solid ceiling to the roof Take out the gasket, metal ring and nut inside the expansion screw, ﬁx the threaded rod in the marked position, and then drive the...
Page 28 5、Pass the main body of the product through the lower side of the slotted hole in the ceiling, and use nuts to hoist it on the threaded rod. This step requires at least two people to cooperate. Roof ① Ceiling ②...
Page 29 6、After ﬁxing the product, observe the distance between the eaves of the housing and the ceiling, and adjust the lifting nuts appropriately to ensure that the eaves of the housing are completely attached to the ceiling. 7、 Insert the power cord;...
Page 30 8、Install the decorative board on the left and right end covers. The way to disassemble the decorative board is to insert and pull out in the horizontal direction to complete the installation. Note: Do not push and pull the decorative panel up and down, as it may cause the buckle of the decorative panel to break.
Page 31: Screen Running
Screen Running Voltage information: make sure your screen is working at the correct voltage , depending on the area. (Using the wrong voltage may cause the screen to become inoperable) (1) Plug the screen power cord into the correct power outlet. (2) When the product power is turned on, a "beep"...
Page 32: Remote Control
Remote Control —— wireless RF remote control (1) Wireless RF remote control: when the screen is hidden and installed in the slot or requires remote control, wireless remote control can be used. It can control the screen without aiming at the IR receiver. Stop Down Front of remote control...
Page 33 For convenient access, the remote controller can be ﬁxed on the wall surface and other planes through the bracket.( wall screw or double-sided adhesive tape can be used for ﬁxation) Inside the wall Outside of a wall...
Page 34 When the remote control needs charging, as shown in the ﬁgure below, unscrew the cover of the remote control with a small screw, then replace the new button battery, close the cover of the remote control, and tighten the screw to prevent the loose battery from falling off;...
Page 35: Screen Height Limit Setting
Screen hight limit setting Black border up (adjust shorter the ﬁxed height of the screen) (The longest position of the screen has been set at the factory, no longer height can be adjusted) If the screen is too low, follow the steps below to ﬁx the screen to the desired position. 1.
Page 36 white adjusting hole Insert the adjust rod into the white adjusting hole in the Stand at the bottom of the screen with the help of light source to ﬁnd the hole position. housing, and then slowly rotate it clockwise for several turns (rotate one circle and adjust the screen height about 2cm) Press the "down"...
Page 37: Black Border Down
Black border down (adjust longer the ﬁxed height of the screen) If adjustment the black border of the screen is too short, please follow the following steps: (please note: it is not allowed to carry out this step directly without adjusting the screen to be short in previous step） (1) Please press the "Down"...
Page 38 White adjusting hole Insert the adjust rod into the white adjusting hole of the Stand at the bottom of the screen shell, and then rotate it slowly for several turns anti-clockwise with the help of (rotate one circle to adjust the screen height about 2cm) light source to ﬁnd the hole position Press the "down"...
Page 39: Screen Maintenance
Screen Maintenance Cleaning requirements: 1. In general, please use a soft brush to clean the screen surface. Remember to use a special soft brush and gently brush away the impurities along the screen grain direction. 2. Do not use any cloth (coarse cloth, soft cloth, gauze, wet cloth) to wipe the screen surface. 3.
Page 40: Manufacturer's Warranty
Manufacturer's Warranty Thank you for choosing VIVIDSTORM screens for your home or business. We are committed to providing high-quality products that meet your expectations. To ensure your satisfaction and peace of mind, we offer the following warranty policy for VIVIDSTORM screens: 1.
Page 41 8. Limitation of Liability: VIVIDSTORM'S liability under this warranty is limited to the repair or replacement of the defective screen or its components as stated above. VIVIDSTORM shall not be liable for any indirect, consequential, or incidental damages arising from the use or inability to use the screen.
Page 42: Certificate
Certiﬁcate Product Name: Product Model No: Factory serial No： Inspector: Date of production： The product has been tested and inspected after operation，and all the tests and inspections have been in accordance with the technical requirements，and its quality meets the speciﬁed requirements.Only after passing the inspection can they be allowed to leave the factory.

VIVID STORM PHANTOM Recessed In-Ceiling Motorized Tension UST ALR User Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for VIVID STORM PHANTOM Recessed In-Ceiling Motorized Tension UST ALR

Summary of Contents for VIVID STORM PHANTOM Recessed In-Ceiling Motorized Tension UST ALR

Table of Contents