Package Contents Contents of Package: D-Link Air DWL-120 2.4 GHz Wireless USB Adapter Manual, Warranty and Drivers on CD Quick Installation Guide If any of the above items are missing, please contact your reseller. System Requirements: A computer with an available USB port...
Introduction The D-Link Air DWL-120 2.4GHz Wireless USB Adapter is an ideal way to extend the reach and number of computers connected to your wireless network. After completing the steps outlined in the Quick Installation Guide (included in your package) you will have the ability to share information and resources, such as files and printers, and take full advantage of a “connected”...
Features and Benefits Provides high-speed wireless connection at up to 11Mbps Operates in the 2.4 to 2.4835 GHz Direct Sequence Spread Spectrum Supports wireless data encryption with 64-bit WEP and 128-bit WEP for more secure networking Supports infrastructure networks via an Access Point and peer-to- peer communication in ad-hoc mode User-friendly configuration and diagnostic utilities Cost-effective wireless solution...
Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Wireless Basics (continued) People use wireless LAN technology for many different purposes: Mobility - Productivity increases when people have access to data in any location within the operating range of the WLAN. Management decisions based on real-time information can significantly improve worker efficiency. Low Implementation Costs –...
Wireless Basics (continued) The DWL-120 is compatible with the D-Link Air 802.11b family of products which include: 2.4GHz Wireless Cardbus Adapters used with laptop computers (DWL-650) 2.4GHz Wireless PCI cards used with desktop computers (DWL-520) Wireless Access Points (DWL-900AP) Standards-Based Technology Based on the IEEE 802.11b standard, the DWL-120 is interoperable with...
Wireless Basics (continued) Installation Considerations The D-Link Air DWL-120 lets you access your network, using a wireless connection, from virtually anywhere. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Getting Started With its default settings, the DWL-120 will connect with other D-Link Air products, right out of the box. There are basically two modes of networking: Infrastructure – using an Access Point, such as the DWL-900AP+. Ad-Hoc – directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DWL-120 wireless network USB adapters.
Connect the Cable or DSL modem to your broadband router (see the Quick Installation Guide included with your router.) Install the D-Link Air DWL-120 wireless USB adapter into an available USB port on your desktop computer. (See the Quick Installation Guide included with the DWL-120.)
Getting Started Setting up a Wireless Ad Hoc Network Install the D-Link Air DWL-120 Wireless USB adapter into the desktop computer. See the Quick Installation Guide included with the product for installation instructions Install a wireless network adapter into the laptop computer. In the example above the DWL-650+ or DWL-650 may be installed into a laptop computer.
With its default settings, the DWL-120 will connect with other D-Link Air products, right out of the box. D-Link Air DWL-120 uses the Configuration Utility as the management software. The utility provides the user an easy interface to change any settings related to the wireless adapter.
Default Setting: Reverts the DWL-120 back to its factory default settings WEP Setting: Will allow you to configure the Encryption for your DWL-120. By default WEP is disabled. Advanced Setting: To configure advanced settings for Power, RTS and Fragmentation Threshold.
Using the Configuration Utility Configuration>WEP Setting WEP type: Select 128 bit WEP or 64 bit WEP encryption Default Key ID: 1 is the default key, or you may select a key from 1-4 Input WEP keys: Input up to 4 WEP keys in hexadecimal format Click OK if you have made any changes Configuration>Advanced Setting Fragmentation Threshold:...
Using the Configuration Utility Profiles New: Click New to create a new profile; a pop-up window will appear allowing you to configure the new profile. (See the example on the next page.) Remove: Highlight the profile you wish to remove; click Remove Edit: Highlight the profile you wish to edit;...
Using the Configuration Utility Network Type: Select Infrastructure or Ad-Hoc SSID: All devices on the network must share the same SSID to be able to communicate TxRate: Choose the data rate speed WEP: Choose Enable or Disable. Disable is the default setting. If you enable WEP, you must Enable WEP on all devices on the network, in order to communicate.
Using the Configuration Utility About About tab displays the utility (firmware) version.
Networking Basics Using the Network Setup Wizard in Windows XP In this section you will learn how to establish a network at home or work, using Microsoft Windows XP. Note: Please refer to websites such as http://www.homenethelp.com http://www.microsoft.com/windows2000 for information about networking computers using Windows 2000, ME or 98SE.
Networking Basics Please follow all the instructions in this window: Click Next In the following window, select the best description of your computer. If your computer connects to the internet through a gateway/router, select the second option as shown. Click Next...
Networking Basics Enter a Computer description and a Computer name (optional.) Click Next Enter a Workgroup name. All computers on your network should have the same Workgroup name. Click Next...
Networking Basics Please wait while the Network Setup Wizard applies the changes. When the changes are complete, click Next. Please wait while the Network Setup Wizard configures the computer. This may take a few minutes.
Networking Basics In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next. Insert a disk into the Floppy Disk Drive, in this case drive A.
Networking Basics Please read the information under Here’s how in the screen below. After you com- plete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue click Next.
Networking Basics Please read the information on this screen, then click Finish to complete the Network Setup Wizard. The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network.
Networking Basics Naming your Computer To name your computer, please follow these directions:In Windows XP: Click Start (in the lower left corner of the screen) Right-click on My Computer Select Properties and click Select the Computer Name Tab in the System Properties window.
Networking Basics Naming your Computer In this window, enter the Computer name Select Workgroup and enter the name of the Workgroup All computers on your network must have the same Workgroup name. Click OK Checking the IP Address in Windows XP The wireless adapter-equipped computers in your network must be in the same IP Address range (see Getting Started in this manual for a definition of IP Address Range.) To check on the IP Address of the adapter, please do the following:...
Networking Basics Checking the IP Address in Windows XP This window will appear. Click the Support tab Click Close Assigning a Static IP Address in Windows XP/2000 Note: Residential Gateways/Broadband Routers will automatically assign IP Ad- dresses to the computers on the network, using DHCP (Dynamic Host Configura- tion Protocol) technology.
Networking Basics Assigning a Static IP Address in Windows XP/2000 Double-click on Network Connections Right-click on Local Area Connections Double-click on Properties...
Networking Basics Assigning a Static IP Address in Windows XP/2000 Click on Internet Protocol (TCP/IP) Click Properties Input your IP address and subnet mask. (The IP Addresses on your network must be within the same range. For example, if one computer has an IP Address of 192.168.0.2, the other computers should have IP...
Networking Basics Checking the Wireless Connection by Pinging in Windows XP and 2000 Go to Start > Run > type cmd. A window similar to this one will appear. Type ping xxx.xxx.xxx.xxx, where xxx is the IP Address of the Wireless Router or Access Point.
Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DWL-120. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows XP. If you have another operating system, these solutions will still apply although the appearance on your computer screen may differ.)
Double-click on Network Adapters Right-click on D-Link Air DWL-120 Wireless USB Adapter D-Link Air DWL-120 Wireless USB Adapter Select Properties to check that the drivers are installed properly D-Link Air DWL-120 Wireless USB Adapter D-Link Air DWL-120 Wireless USB Adapter...
RF noise, like microwaves, Monitors, electric motors, etc. 4. Why can’t I get a wireless connection? If you have enabled Encryption on the DWL-120, you must also enable encryp- tion on all wireless devices in the network in order to establish a wireless con- nection.
Technical Specifications Standard IEEE 802.11b WIFI Certified Diagnostic LED Power Link Status Temperature Operating: 0ºC to 55ºC (32ºF to 131ºF) Storing: -20ºC to 75ºC (-4ºF to 167ºF) Humidity: 95%, non-condensing Antenna Type: Integrated Modulation Technique: DSSS Physical Dimensions: L = 3.3 inches W = 2.1 inches H = 0.2 inches Data Rates:...
Contacting Technical Support You can find the most recent software and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States for the duration of the warranty period on this product. U.S. customers can contact D-Link technical support through our web site, or by phone.
D-Link’s sole obligation shall be to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund at D-Link’s sole discretion. Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not be new or have an identical make, model or part.
RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT.
Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help Registration: Register your D-Link Air DWL-120 online at http://support.dlink.com/register...