Advertisement
to
licensed
1739 Digital answering system
This manual contains information about
this product's installation and operation.
Please also read Part 1 - Important
product information.
For customer service or product information,
visit our website at
1 (800) 222-3111
or call
1 (866) 288-4268
07/11.
AT&T
Telephones.
American
Advanced
7�21�.
7�21�.
T��
T��
Antonio,
Antonio,
Property
Intellectual
Reserved.
Rights
All
Telephones.
www.telephones.att.com
www.telephones.att.com
. In Canada, dial
.
13
Issue
China.
in
Printed
of
trademark
a
is
�an
�an
Telephones,
American
AT&T
of
trademarks
are
American
Advanced
Guard®
Message
Advanced
logo
AT&T
the
and
AT&T
2007-2011
©
User's manual
Part 2
Advertisement
Table of Contents
Related Manuals for AT&T 1739
Summary of Contents for AT&T 1739
-
Page 1: Product Information
Part 2 User’s manual 1739 Digital answering system This manual contains information about this product’s installation and operation. Please also read Part 1 - Important product information. For customer service or product information, www.telephones.att.com visit our website at 1 (800) 222-3111 or call . -
Page 2: Installation
If you subscribe to high-speed Internet service (D�L - digital subscriber line) through your telephone line, you must install a D�L filter between the telephone line cord and the telephone wall jack. The filter prevents noise and caller ID problems caused by D�L interference. Please contact your D�L... -
Page 3: Feature Setup
Feature setup Feature setup To enter the feature setup mode, press and hold SETUP until the system announces “Language is...” Press SETUP repeatedly until you hear the desired feature. /SKIP or When you hear the feature you want to modify, press ANNC /REPEAT to choose the feature’s setting. - Page 4 NOTE: For this feature to work, you must subscribe to caller ID service from your telephone service provider. There may be a fee for this service, and it may not be available in all areas. Store number “Store number •...
- Page 5 Before playing each message, the system announces the day and time the message was received. If Store number is activated, the system also announces the caller’s telephone number (see Store number under Feature setup on page 3). After playing the last message, the system announces “End of messages.“ •...
- Page 6 To check the date and time, press CLOCK. NOTE: In the event of a power failure, see the instructions on the bottom of the unit to reset the clock. If the clock is not set the system will announce, “Time and day not set,” before playing each message.
- Page 7 If the number announce feature is on, the caller’s telephone number will be announced. NOTE: If you set the volume level to 0, the system will automatically adjust to an audible level (level 2) during call screening, or when listening to messages or changing feature settings. You may need to adjust the volume level afterwards.
- Page 8 If the clock is not set when the message was recorded, or there was a power failure after it was set, the system will announce “Time and day not set,” after the time and day. After playing the last message, the system announces, “End of messages.“...
- Page 9 0 (Rotating) Deleting all old messages. Memory is full. F (Flashing) The number of rings before the system answers a call. Toll saver is set to 2/4. Toll saver is set to 4/6. The selected feature is on. The selected feature is off.
-
Page 10: Remote Operation
The system announces the number of messages, then begins playing back the messages. If the announcement continues to play after you have entered your remote access code, wait for the announcement to end, then enter the code again. -
Page 11: In Case Of Difficulty
The system does not answer after the correct number of rings. • If the toll saver feature is on, the number of rings changes from 4 to 2, or 6 to 4, when there are new messages waiting. •... -
Page 12: General Product Care
If the system is disconnected from its AC power, it will not operate. The announcement and messages are retained in memory during a power failure, but it will be necessary to reset the clock. �ee the instructions at the bottom of the answering machine.
Need help?
Do you have a question about the 1739 and is the answer not in the manual?
Questions and answers
how do i record a message for the machine to answer with
To record a message (memo) on the AT&T 1739 answering machine:
1. Press and hold the MEMO/REPEAT button.
2. Wait for the beep, then speak toward the microphone at the lower right corner of the system.
3. Release the button to stop recording.
The memo can be up to 3 minutes long and is stored as an incoming message.
This answer is automatically generated
how to change language from Spanish to English on auto instructions on ATT answering machine
To change the language from Spanish to English on the AT&T answering machine model 1739:
1. Press SETUP repeatedly until you hear “Language is...”.
2. Press ANNC/SKIP or MEMO/REPEAT to select English.
3. Press SETUP to save and move to the next setting, or press PLAY/STOP to save and exit.
This answer is automatically generated
how to change language from spanish to English on answering machine instructions
To change the language from Spanish to English on the AT&T answering machine model 1739:
1. Press SETUP repeatedly until you hear "Language is...".
2. Press ANNC/SKIP or MEMO/REPEAT to select English.
3. Press SETUP to save and move to the next setting, or press PLAY/STOP to save and exit.
This answer is automatically generated