Option Menu - Yamaha HTR-6150 Owner's Manual

3 OPTION MENU

Use this menu to adjust the optional system parameters.
;MANUAL SETUP
3 OPTION MENU 1/2
. A)DISPLAY SET
B)MEMORY GUARD
C)AUDIO SELECT
D)PARAM. INI
[ ]/[ ]:Up/Down
[ENTER]:Enter
■ Display settings
3 OPTION MENU
A)DISPLAY SET 1/2
DIMMER;;;;;;;;;0
VIDEO CONV;;;;ON
FL SCROLL;;;CONT
[ ]/[ ]:Up/Down
p [
[ ]/[ ]:Select
Dimmer DIMMER
Use this feature to adjust the brightness of the front panel
display.
Control range: –4 to 0
Control step: 1
• Press 8 l to make the front panel display dimmer.
• Press 8 h to make the front panel display brighter.
VIDEO CONV.
Video conversion
Use this feature to set whether to convert the video signals
input at the VIDEO and S VIDEO jacks.
Choices: ON, OFF
• Select "ON" to convert composite and S-video signals
interchangeably, or to convert composite and S-video
to component video signals.
• Select "OFF" not to convert any signals.
Notes
• This unit does not convert 480 line video signals and 576 line
video signals interchangeably.
• The converted video signals are only output at the MONITOR
OUT jacks. When recording a video source, you must make the
same type of video connections between each component.
• When composite video or S-video signals from a VCR are
converted to component video signals, the picture quality may
suffer depending on your VCR.
• Unconventional signals input at the composite video or S-video
jacks cannot be converted or may be output abnormally. In such
cases, set "VIDEO CONV." to "OFF".
• When non-standard video signals (such as video signals from a
game console) are input, this unit may not convert the signals
even if you set "VIDEO CONV." to "ON".
;MANUAL SETUP
3 OPTION MENU 2/2
E)BLUETOOTH SET
. F)XM RADIO SET
G)SIRIUS SET
[ ]/[ ]:Up/Down
[ENTER]:Enter
A)DISPLAY SET
3 OPTION MENU
A)DISPLAY SET 2/2
. OSD SHIFT;;;;;;0
OSD-SOURCE;;;30s
OSD-AMP;;;;;;30s
[ ]/[ ]:Up/Down
p [
[ ]/[ ]:Select
Front panel display scroll FL SCROLL
Use this feature to set whether to display the information
(such as a song title or a channel name) in the front panel
display in a continuous manner or by the first 14
alphanumeric characters after scrolling all characters once
when "XM", "SIRIUS" or "DOCK" is selected as the
input source.
Choices: CONT, ONCE
• Select "CONT" to display the operation status in the
front panel display in a continuous manner.
• Select "ONCE" to display the operation status in the
front panel display by the first 14 alphanumeric
characters after scrolling all characters once.
OSD shift OSD SHIFT
Use this feature to adjust the vertical position of the OSD.
Control range: –5 (downward) to +5 (upward)
Control step: 1
Initial setting: 0
• Press 8 l to lower the position of the OSD.
• Press 8 h to raise the position of the OSD.
Source feature OSD display time
OSD-SOURCE
Use this feature to set the amount of time to display the
XM Satellite Radio information, SIRIUS Satellite Radio
information or iPod menu in the OSD after you perform a
certain operation.
Choices: ON, 10s, 30s
• Select "ON" to display the OSD unceasingly during an
operation.
• Select "10s" to turn off the OSD 10 seconds after you
perform a certain operation.
• Select "30s" to turn off the OSD 30 seconds after you
perform a certain operation.
Amplifier function OSD display time
OSD-AMP
Use this feature to set the amount of time to display the
status after you perform a certain operation.
Choices: ON, 10s, 30s
• Select "ON" to display the OSD constantly during an
operation.
• Select "10s" to turn off the OSD 10 seconds after you
perform a certain operation.
• Select "30s" to turn off the OSD 30 seconds after you
perform a certain operation.
SET MENU
73
En