Yamaha ACD1 Owner's Manual
Amplifier control device
Hide thumbs
Also See for ACD1:
- Reference manual (25 pages) ,
- Owner's manual (15 pages) ,
- Service manual (125 pages)
Related Manuals for Yamaha ACD1
Summary of Contents for Yamaha ACD1
- Page 1 Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones Manuale di istruzioni Руководство пользователя...
- Page 2 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. (UL60065_03) ACD1 Owner’s Manual...
- Page 3 • This apparatus contains a lithium battery for memory back- BROWN : LIVE As the colours of the wires in the mains lead of this apparatus • Raadpleeg uw leverancier over de verwijdering van de bat- may not correspond with the coloured markings identifying the...
- Page 4 Yamaha service personnel. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Power supply/Power cord •...
- Page 5 [Checking for the correction] If the two alphabetical characters at the beginning of the serial number label on the back of the power amp are IL, IM, IN, IO, IP, IX, IY, IZ, or JH, and no green circular label is affixed immediately nearby it, then the product has not been corrected.
-
Page 6: Table Of Contents
Preparation ..........................10 Connection Examples ..................11 Connections with the PC-N or Tn series................12 Connections with the XP, XM, or XH series ................13 Connections with controllers from other manufacturers ............13 Operations that can be performed from the panel ........14 Troubleshooting....................15... -
Page 7: Introduction
Related manuals and software This document explains mainly the initial connection. Manuals that contain detailed explanations of the ACD1 and Amp Editor, as well as the Amp Editor software itself, can be downloaded from the following page of the web- site. -
Page 8: Terms
This section explains terminology specific to the ACD1. ■ Scene Settings such as power-on/standby or mute for each amplifier are called a “scene.” By recalling a scene, the saved settings can be immediately applied to the amplifiers. ■ Scene link Settings for simultaneously recalling scenes for multiple amplifiers within an area are called a “scene link.”... -
Page 9: Precautions When Rack-Mounting The Unit
• Leave the back of the rack open, and allow at least 10 cm of space between the rack and the wall and ceiling to ensure ade- quate cooling. If you’ve installed a fan kit, there may be cases in which closing the back of the rack will produce a greater cooling effect. -
Page 10: Preparation
CAUTION • A small amount of current is flowing even when the power switch is off. If you will not be using this device for an extended period of time, be sure to disconnect the power plug from the AC outlet. -
Page 11: Connection Examples
• In the United States or Canada, the Ethernet cables that connect the ACD1 to the computer or network switch should be STP cables in order to avoid electromagnetic interference. -
Page 12: Connections With The Pc-N Or Tn Series
Make the appropriate AMP ID and terminator settings using the [AMP ID] switches located on the rear panel of the connected amplifiers. Specify a different AMP ID for each amplifier that is connected to the same ACD1. The AMP ID will be the total of the values of the switches that are set to ON. -
Page 13: Connections With The Xp, Xm, Or Xh Series
If you connect an Ethernet-compatible remote controller, you must set the ACD1 IP Port number by using [6.Network Setup] → [IP Ctrl Port #] on the ACD1 unit. Alternatively, in Amp Editor you can click the [Device Setup] menu command [IP Control Port No.] and open the “IP Control Port No.”... -
Page 14: Operations That Can Be Performed From The Panel
The following operations can be performed from the ACD1’s front panel. • For details, refer to the ACD1 Reference Manual. NOTE • Before use, remove the transparent protective film that was applied to the LCD prior to shipment from the factory. Category Sub category Operation performed 1. -
Page 15: Troubleshooting
You can initialize the ACD1’s internal memory. • The log data is preserved even if you execute initialization. NOTE • When you initialize the internal memory, the content that had been saved in memory (scenes for each amp, and ACD1 settings) will be lost. CAUTION Use caution when performing the following steps. - Page 16 [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authori- ties or dealer and ask for the correct method of disposal.
- Page 17 2002/96/EC. Al disponer de estos productos correctamente, ayudará a ahorrar recursos valiosos y a prevenir cualquier potencial efecto negativo sobre la salud humana y el medio ambiente, el cual podría surgir de un inapropiado manejo de los desechos.
- Page 18 MEMO ACD1 Owner’s Manual...
- Page 19 Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo.
- Page 20 Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2009 Yamaha Corporation WM15360 909POCP?.?-02B0 Printed in Japan...