Teletype 35 Adjustments

TELETYPE CORPORATION
Skokie, Illinois , U.S . A.
SECTION 574-224 -700TC
Issue 4, August, 1963
1.
2.
35 NON-TYPiiNG REPERFORA TOR
ADJUSfMENTS
CONT~TS
PAGE
GENERAL . . . • . . . . . . . . . . . . . 1-4
ADJUSfMENTS. . . . . . . . . . . . . . 4-38
i\djustll\g arm torsion spring . . . . . 1'9
Armature bail spring (bksp. ) . . . . . 3
8
Armature hinge (bksp. ) . . . . . . . . . 33
Armature up-stop (bkap.) . . . . . . . 33
Bell crank spring (bksp.) . . • . . . . 3 8
Clutch shoe lever . . . . . . • • . . . • • 5
Clutch sooe lever spring . . . . . . . .
6
Clutch sooe spring . . . . . . . . . . . . 6
Detent lever spring. . . . . . . . . . . . 30
Dl'lve lli:lk (bksp.) . . • • . . . . . • • . 34
Feed hole spacing . . . . . . . . . . • • 27
Feed hol e spacing (final) . . • • • • . •
2'1
Feed hol e spacing (preliminary) . . •
2'1
Feed pawl. • • • . • • • • • . . • . • . • • 25
Feed pawl clearance (bksp. ). . . • . •
32
Feed pawl (prelimi . n ary (bksp.) ). . . 32
Feed pawl spring . . . • . • • . . . • • • 30
Feed pawl apring (bksp.) . . . • . . . . 38
Final power or manual (bksp.) . . . . 35
Follower lever . . . • . • . . • • • • • . 19
Function clutch drum end play . . . . 5
Function clutch latch lever apring . . 6
Function clutch release spring . . . . 18
Function clutch
trip
lever . . . . . . . l
'1
Latch (bksp. ) . . • . . . . . . . . • • . .
36
Latch extension (bksp.). . . . • . • . . 35
Latch extension spring (bksp. ) . . . . 38
Latch lever clearance . . . . . . . . . . 25
Lateral and front to rear feed
wheel position (early deSign). • . . 26
Lateral and front to rear feed
wheel position (latest design) . . .
28
Main
trip
lever spring . . . . . . . • . 19
Marking lock lever spring . . . . • . .
12
Non-repeat latch (bksp.) . . . • • . . . 37
Perforator drive link spring . . . . . 22
Perforator position (final) . . . . . . . 21
Perforator position (preliminary) . . 21
Punch pin penetration . . . . . . . . . . 23
Punch slide downstop position . . . . 23
Punch slide guide . . . . . . • . • • • . . 23
Punch
and
feed slide latch springs . 19
Punch slide spring . . . . . . • . • . . . 29
Push lever reset bail spring . . . . . 14
CONTENTS
PAGE
Range finder !mob phasil\g . . . • • . . 15
Release downstop bracket . . . . . . . 18
Reset arm . . . . . . . . . . • . . . • . . 17
Reset ball trip lever . . . . . • . . . . . 2
4
Rocker ball. . . • . . . . . . . 20
Rocker ball guide bracket . , . . . . . 20
Selector armature . . . . . . . • . • . . 8
Selector armature downstop
bracket . . • . . . . . . • • . . . . . . .
8
Selector armature spring (final) . . . 10
Selector armature spring (
units employing selector arma-
ture with single anti - freeze
button only) . . . • . • • . • • . • • . •
9
Selector armature spring (For
units
employing selector arma-
ture with two anti-freeze
buttons only) . . • . • . . . • . . . . . 10
Selector cam lubricator . . • . • • • . 7
Selector clutch drum • . . . . . • • . . 13
Selector clutch latch lever spring . . 14
Selector clutch stop arm . . • • . • • • 15
Selector lever apring • . . • . . . . . • 13
Selector magnet bracket . • . . . • • •
11
Selector oil shield . • • . • • . • . . . •
7
Selector push lever spring . . . • . . . 13
Selector receiving margin . . . . . . . 16
!:pacing lock lever spr i ng . . . . . . . 14
Start iever apring . . • . . . . . . . . . 16
Tape depressor slide spring . . . . . 31
Tape guide . . . . . . . • • . . • . . . • • 3
I
Tape guide apring (punch block) . . . 29
Tape guide apring (tape chute) • . . . 29
Tape shoe torsion aprtng . . . . . • . . 31
Toggle ball eccentric (preliminary) . 22
Toggle operating arm • . . . . . . . . . 22
Trip cam follower lever . . . . • . • • 19
1. GENERAL
1.
01 This section is reissued to:
(a) Include recent engtneering changes.
(b) Include armature with two anti - freeze
buttons .
©
Teletype Corporation 1962
Printed in U.
S.
A.
Page 1