Teletype 35 Adjustments

TELETYPE CORPORATION
SECTION 574-224-700
Skokie, Illinois, U. S. A.
Issue 4, August, 1963
35 NON-TYPING REPERFORATOR
ADJUSTMENTS
CONTENTS
PAGE CONTENTS PAGE
1. GENERAL 1-4
Range finder knob phasing 15
Release downstop bracket
18
2.
ADJUSTMENTS
4-38 Reset arm 17
Reset bail trip lever 24
Adjusting arm torsion spring 19 Rocker bail 20
Armature bail spring (bksp.) 38 Rocker bail guide bracket 20
Armature hinge (bksp.) ..... . . . .
33 Selector armature 8
Armature up-stop (bksp.)
33 Selector armature downstop
Bell crank spring (bksp.) 38
bracket 8
Clutch shoe lever 5
Selector armature spring (final) . . . 10
Clutch shoe lever spring 6
Selector armature spring (
Clutch shoe spring 6
units employing selector arma-
Detent lever spring
30
ture with single anti-freeze
Drive link (bksp.)
34 button only) . . . . . . . . . . . . . . .
9
Feed hole spacing
27 Selector armature spring (For
Feed hole spacing (final)
27 units employing selector ar ma-
Feed hole spacing (preliminary) . . 27
ture with two anti-freeze
Feed pawl. . . ....... 0 . . . . . 0 0
25 buttons only) 10
Feed pawl clearance (bksp.)
32 Selector cam lubricator 7
Feed pawl (preliminary (bksp.) ). . .
32 Selector clutch drum ...... . . . 13
Feed pawl spring
30 Selector clutch latch lever spring . . 14
Feed pawl spring (bksp.)
38 Selector clutch stop arm . . . . . . . . 15
Final power or manual (bksp.) . . .
35 Selector lever spring
13
Follower lever 19 Selector magnet bracket ...... . . 11
Function clutch drum end play . . . 5 Selector oil shield . . . . . . . . . . . . 7
Function clutch latch lever spring . 6
Selector push lever spring 13
Function clutch release spring . . . . 18
Selector receiving margin . . 0 . . . 16
Function clutch trip lever
17 Spacing lock lever spring 14
Latch (bksp.) 36
Start lever spring 16
Latch extension (bksp.) 35
Tape depressor slide spring 31
Latch extension spring (bksp.) . . . .
38 Tape guide 31
Latch lever clearance
25 Tape guide spring (punch block) . . . 29
Lateral and front to rear feed
Tape guide spring (tape chute) . . . . 29
wheel position (early design). . . .
26
Tape shoe torsion spring
31
Lateral and front to rear feed
Toggle bail eccentric (preliminary) 22
wheel position (latest design) . . .
28 Toggle operating arm 22
Main trip lever spring
19
Trip cam follower lever . . 0 .
19
Marking lock lever spring
12
Non-repeat latch (bksp.) 37
Perforator drive link spring 22
10 GENERAL
Perforator position (final) 21
Perforator position (preliminary) . 21 1.01 This section is reissued to:
Punch pin penetration
23
Punch slide downstop position . . .
23
Punch slide guide 23
(a) Include recent engineering changes.
Punch and feed slide latch springs 19
Punch slide spring ...... 0 . . . .
29 (b) Include armature with two anti - freeze
Push lever reset bail spring
14 buttons.
0 Teletype Corporation 1962
Printed in U0 S. A. Page 1