Subscribe to Our Youtube Channel
Related Manuals for Seagate IRONWOLF PRO ST12000NE0007
Summary of Contents for Seagate IRONWOLF PRO ST12000NE0007
- Page 1 SATA Product Manual Standard 512E models ST12000NE0007 100818529, Rev. B Gen 4 - October 2017...
- Page 2 Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. IronWolf, PowerChoice and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. The FIPS logo is a certification mark of NIST, which does not imply product endorsement by NIST, the U.S., or Canadian governments.
-
Page 3: Table Of Contents
Storage ................16 2.10.3 Seagate® Rescue™ Data Recovery Service Program Terms (for +Rescue models) ..17 2.11 Agency and Safety Certifications . - Page 4 S.M.A.R.T. commands............. . 33 Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B...
-
Page 5: Seagate® Technology Support Services
For information regarding online support and services, visit: http://www.seagate.com/contacts/ For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/recover/ For Seagate OEM, Distribution partner and reseller portals, visit: http://www.seagate.com/partners/ Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... -
Page 6: Introduction
Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. The specification can be downloaded from www.serialata.org. Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... -
Page 7: Drive Specifications
Non-Operating (Ambient °C) –40° to 70° Operating ambient temperature (min °C) 5° † Operating temperature (drive case max °C) 60° 20°C (operating) Temperature gradient (°C per hour max) 30°C (non-operating) Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... - Page 8 † Seagate does not recommend operating at sustained case temperatures above 60°C. Operating at higher temperatures will reduce useful life of the product. Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B...
-
Page 9: Formatted Capacity
I/O data-transfer rate (MB/s max) 600 (Ultra DMA mode 5) Start/stop times Power-on to Ready (sec) (typ/max) 20/30 Standby to Ready (sec) (typ/max) 20/30 Ready to spindle stop (sec) (max) Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... -
Page 10: Power Specifications
7.85 Maximum DC (peak) 0.921 1.779 *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... -
Page 11: Conducted Noise
10MHz. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. Note 2.5.3 Voltage tolerance Voltage tolerance (including noise): 5V ± 5% 12V ± 10% Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... -
Page 12: Extended Power Conditions - Powerchoicetm
• Saved enabled state, and timer value • Current enabled state, and timer value S.M.A.R.T. Read Data Reports • Attribute 192 - Emergency Retract Count • Attribute 193 - Load/Unload Cycle Count Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... - Page 13 Disable EPC Feature Set PowerChoice Supported Extended Power Condition Identifiers Power Condition Identifiers Power Condition Name Standby_z 01 - 80 Reserved Idle_a Idle_b Idle_c 84 - FE Reserved All EPC Power Conditions Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B...
-
Page 14: Environmental Limits
Non-operating –40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This specification assumes that the drive is packaged in the shipping container designed by Seagate for use with drive. Temperature Check Point Figure 2. -
Page 15: Shock
The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below. 2–500 Hz 2.27 Grms ref Linear Random Freq (Hz) .001 .001 Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... -
Page 16: Acoustics
Test for Prominent Discrete Tones (PDTs) Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO 389-7) to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. -
Page 17: Reliability
None required. 2.10.2 Storage Maximum storage periods are 180 days within original unopened Seagate shipping package or 60 days unpackaged within the defined non-operating limits (refer to environmental section in this manual). Storage can be extended to 1 year packaged or unpackaged under optimal environmental conditions (25°C, <40% relative humidity non-condensing, and non-corrosive... -
Page 18: Seagate® Rescue™ Data Recovery Service Program Terms (For +Rescue Models)
US, please visit our website for numbers in your local and language: http://www.seagate.com/services-software/recover/resources/. An SRS representative will review your case to confirm your eligibility, and to assess whether your data may be recoverable by remote recovery services or whether you will need to send your device to SRS for in-lab servicing. - Page 19 Seagate reserves the right to refuse service to or the return of any storage devices that have been determined to violate these regulations.
-
Page 20: Agency And Safety Certifications
Seagate drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with all relevant regulatory requirements and standards for the drives, Seagate cannot guarantee that all system-level products into which the drives are installed comply with all regulatory requirements and standards applicable to the system-level products. The drive is designed for operation inside a properly designed system (e.g., enclosure designed for the drive), with properly shielded I/O cable (if... -
Page 21: Morocco Commodity Mark
2.11.6 Morocco Commodity Mark To satisfy our OEM customers, Seagate has added the Moroccan Commodity Mark to the drives provided to the OEM for the sale of Customer Kits produced by our OEM customers that are intended to be incorporated into the OEM's finished system-level product by an end user. -
Page 22: Environmental Protection
2.12.1.1 Restriction of Hazardous Substances in Electrical and Electronic Equipment Seagate drives are designed to be compliant with the European Union RoHS "Recast" Directive 2011/65/EU (RoHS 2) as amended by Directive (EU) 2015/863. The RoHS2 restricts the use of certain hazardous substances such as Lead, Cadmium, Mercury, Hexavalent Chromium, Polybrominated Biphenyls (PBB) and Polybrominated Diphenyl Ether (PBDE), BisBis(2-Ethylhexyl) phthalate (DEHP), Benzyl butyl phthalate (BBP), Dibutyl phthalate (DBP), and Diisobutyl phthalate (DIBP) in electrical and electronic equipment (EEE). -
Page 23: Taiwan Requirements - Taiwan Rohs
Taiwan RoHS refers to the Taiwan Bureau of Standards, Metrology and Inspection’s (BSMI) requirements in standard CNS 15663, Guidance to reduction of the restricted chemical substances in electrical and electronic equipment. Seagate products must comply with the “Marking of presence” requirements in Section 5 of CNS 15663, effective January 1, 2018. This product is Taiwan RoHS compliant. -
Page 24: Corrosive Environment
When transporting or shipping a drive, use only a Seagate-approved container. Keep the original box. Seagate approved containers are easily identified by the Seagate Approved Package label. Shipping a drive in a non-approved container voids the drive warranty. Seagate repair centers may refuse receipt of components improperly packaged or obviously damaged in transit. Contact the authorized Seagate distributor to purchase additional boxes. -
Page 25: Configuring And Mounting The Drive
For installations which require cables, users can connect the drive as illustrated in Figure 3. Figure 3. Attaching SATA cabling Each cable is keyed to ensure correct orientation. IronWolf Pro Serial ATA drives support latching SATA connectors. Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... -
Page 26: Drive Mounting
1.028 MAX 26.11MM .138±.015 2 2.000 C L OF DRIVE Figure 4. Mounting configuration dimensions The image is for mechanical dimension reference only and may not represent the actual drive. Note Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... -
Page 27: Serial Ata (Sata) Interface
There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane config- uration. All used voltage pins (V ) must be terminated. Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... -
Page 28: Supported Ata Commands
/ 0011 Sanitize Device - Freeze Lock Ext / 0020 Sanitize Device - Status Ext / 0000 Security Disable Password Security Erase Prepare Security Erase Unit Security Freeze Security Set Password Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... - Page 29 Write FPDMA Queued Write Log DMA Ext Write Log Extended Write Multiple Write Multiple Extended Write Multiple FUA Extended Write Sectors Write Sectors Without Retries Write Sectors Extended Write Uncorrectable Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B...
-
Page 30: Identify Device Command
Advanced PIO modes supported (modes 3 and 4 supported) 0003 Minimum multiword DMA transfer cycle time per word (120 ns) 0078 Recommended multiword DMA transfer cycle time per word (120 ns) 0078 Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... - Page 31 Bits 7:2 indicate individual SCT feature support. 207-254 ATA-reserved 0000 Integrity word xxA5 See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data. Note Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B...
- Page 32 Ultra DMA mode 2 is currently active. Ultra DMA mode 3 is currently active. Ultra DMA mode 4 is currently active. Ultra DMA mode 5 is currently active. Ultra DMA mode 6 is currently active. Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B...
-
Page 33: Set Features Command
Enable read look-ahead (read cache) feature (default). Report full capacity available At power-on, or after a hardware or software reset, the default values of the features are as indicated above. Note Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... -
Page 34: Commands
S.M.A.R.T. Disable Operations S.M.A.R.T. Return Status If an appropriate code is not written to the Features Register, the Note command is aborted and 0x 04 (abort) is written to the Error register. Seagate IronWolf Pro v4 Serial ATA Product Manual, Rev. B... - Page 35 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100818529, Rev. B...
Need help?
Do you have a question about the IRONWOLF PRO ST12000NE0007 and is the answer not in the manual?
Questions and answers