Download Print this page

Haier HSU09VHJ Installation Manual

Room air conditioner
Hide thumbs

Advertisement

Quick Links

Installation Manual of Room Air Conditioner

Preparation
Necessary Tools for Installation
Hammer
Nipper
Hacksaw
Hole core drill
Spanner(17,19 and 26mm)
Gas leakage detector or
soap-and-water solution
Power Source
Before inserting power plug into receptacle, check the voltage without fail.
The power source is the same as the corresponding name plate.
Install an exclusive branch circuit of the power.
A receptacle shall be set up in a distance where the power cable can be
reached.Do not extend the cable by cutting it.
Drawing for the installation of indoor and outdoor units
The models adopt HC FC free refrigerant R410A
more than 10cm
(3 7/8)
more than
10cm (3 7/8)
Arrangement of piping
directions
Rear left
Rear
Left
right
Right
Below
more than 20cm
The marks from
to
A
in the figure are the
G
parts numbers.
The distance between
the indoor unit and the
floor should be more
than 2m.
more than 60cm
(23 5/8)
The above picture is for your reference only. Your product may look different.
Read this manual before installation.
Explain the operation of the unit to the user according to this manual.
NO.00105
Torque wrench
(17mm,22mm,26mm)
Pipe cutter
Flaring tool
Knife
Measuring tape
Reamer
Attention must be paid to
the pitch of drain hose
more than 10cm
more than 15cm
(7 7/8)
Selection of Installation Place
Indoor Unit - Select a location that is
Robust not causing vibration, where the body can be supported sufficiently.
Not affected by heat or steam generated in the vicinity, where inlet and outlet of the
unit are not disturbed.
Possible to drain easily, where piping can be connected with the outdoor unit.
Where cold air can be spread in a room evenly.
Nearby a power receptacle. (Refer to drawings).
Place where the distance of more than lm from televisions, radios, wireless apparatuses
and fluorescent lamps can be left.
In the case of fixing the remote controller on a wall, place where the indoor unit can
receive signals when the fluorescent lamps in the room are in use.
Outdoor Unit - Select a location that is
Less affected by rain or direct sunlight and is sufficiently ventilated.
Strong enough to bear the unit, where vibration and noise are not increased.
Not causing a nuisance to neighbors due to discharged air or noise.
Q
A distance marked
is available as illustrated in the below figure.
G
(3 7/8)
F
A
C
(5 1/2)
(5 7/8)
(4 1/2)
D
E
more than 25cm
(9 7/8)
Optional parts for piping
Non-adhesive tape
A
Adhesive tape
B
Saddle (L.S) with screws
C
Connecting electric cable
D
for indoor and outdoor
E
Drain hose
F
Heating insulating material
Piping hole cover
G
Floor fixing dimensions of the
outdoor unit
(Unit:mm / inch)
For:09k 12k 18k
140
500
140
(19 2/3)
(5 1/2)
For:24k
113.5
633
113.5
(24 7/8)
(4 1/2)
Fixing of outdoor unit
Fix the unit to concrete or block
with bolts (10mm) and nuts firmly
and horizontally.
When fitting the unit to wall
surface, roof or rooftop, fix
a supporter securely with nails
or wires in consideration of
earthquake and strong wind.
If vibration may affect the
house, fix the unit by attaching a
vibration-proof mat.

Advertisement

loading

  Also See for Haier HSU09VHJ

  Related Manuals for Haier HSU09VHJ

  Summary of Contents for Haier HSU09VHJ

  • Page 1: Installation Manual Of Room Air Conditioner

    fluorescent lamps can be left. Power Source In the case of fixing the remote controller on a wall, place where the indoor unit can receive signals when the fluorescent lamps in the room are in use. Before inserting power plug into receptacle, check the voltage without fail.
  • Page 2: Indoor Unit

    Wall hole When connecting the cable before installing the indoor unit Pitch downward for drainage Insert the cord from the back side of the unit, then pull it out on the front side. Ø70mm (2 3/4) Fasten the unit wire harness to the conduit holder using the lock nut.
  • Page 3: Outdoor Unit

    Ensure that no dirt or debris enters the pipe. Outdoor unit The standard pipe length is 7m (27 9/16) . If it is over 7m (27 9/16) , the function of the unit will be affected. If the pipe has to be lengthened, the refrigerant should Indoor uni t be charged, according to 20 g/m (0.018 oz/inch).
  • Page 4 Step 1. Step 2. 2-way valve Liquid Side In case that the attached drain hose is in a room, please apply heat insulation to 3-way valve Gas Side Open it without fail. Gaugemanifold(for R410A)
  • Page 5: Fuente De Alimentación

    Antes de insertar el enchufe de alimentación en la toma, compruebe que el voltaje ● Elija un lugar que permita soportar el peso de la unidad y que no amplifique el ruido no falla. La fuente de alimentación es la que figura en la placa de datos nominales.
  • Page 6: Unidad Interior

    1. Pase la manguera aislante a través del hueco de los materiales de aislamiento de calor de la unidad interior. 2. Inserte los cables eléctricos de interior / exterior a través de la parte trasera de la Placa de montaje (1) Codo de drenaje (1) unidad interior y tire de ellos desde la parte delantera.
  • Page 7: Unidad Exterior

    18N.m/13.3Ft.lbs Lado de líquido/gas 9,52mm (3/8") 42 N.m/30.1Ft.lbs 4. Abra el vástago de la válvula de 2 vías 90 grados hacia la izquierda. Después de 6 Lado de gas 12,7mm (1/2") 55N.m/40.6Ft.lbs segundos, cierre la válvula de 2 vías e inspeccione si existen fugas de gas.
  • Page 8 Incorrecto 7. Para evitar fugas de gas, gire el tapón del puerto de mantenimiento y el tapón del vástago de las válvulas de 2 y 3 vías un poco por encima del punto en el que la torsión aumenta súbitamente.
  • Page 9 (17 mm, 22 mm, 26 mm) Pince ● Solide sans vibration et offrant un support suffisant. ● N'est pas affecté par de la chaleur ou de la vapeur générées dans les environs et Scie à métaux Coupe-tube doit garantir que l'entrée et la sortie de l'unité ne seront pas gênées.
  • Page 10: Unité Intérieure

    ● Connectez au préalable le câble des unités intérieures/extérieures et recouvrez ensuite les câbles connectés avec l'isolation. 1. Exécutez une mise à niveau correcte de la plaque à fixer contre le mur en fonction des piliers ou des linteaux autour, puis attachez la plaque temporairement avec un Fixation de l'unité...
  • Page 11: Unité Extérieure

    55N.m/40.6Ft.lbs Clé Clé dynamométrique 4. En tournant dans le sens antihoraire, ouvrez le robinet de la vanne à 2 voies à un Gaz 15,88mm (5/8") 60 N.m/44.3Ft.lbs angle de 90 degrés. Environ 6 secondes plus tard, fermez la vanne à 2 voies et ins-...
  • Page 12 ● Ne pas effectuer la vidange telle qu'illustrée ci-dessous. 7. Pour empêcher toute fuite de gaz, tournez le capuchon de l'orifice d'entretien, le capuchon du robinet des vannes à 2 et 3 voies un peu au-delà du point où le couple augmente brusquement.