Parts And Functions; Indoor Unit; Remote Controller; Outdoor Unit - Haier HSU-09LEK03/ (DB) Operation Manual

Parts and Functions

Indoor Unit

Inlet
Inlet grille
Anion generator
Vertical blade
adjust left and right air flow
Power indicator
Timer mode indicator
(Lights up whenTimer operation is selected.)
Operation mode indicator
(lights up when the compressor is on.)
Remote signal receiver
(A beeping sound is generated when a signal
from remote controller isreceived.)
Ambient temp display
When receiving the remote control signal, display the set
temperature and in the rest time the room temperature is
is displayed and this room temperature is only for reference.
Horizontal flap
adjust up and down air flow Don't adjust it manually
Actual inlet grille may vary from the one shown in the
manual according to the product purchased

Outdoor Unit

OUTLET
INLET

Clock set

Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
or decrease 1min. If the button is kept pressed,time will
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
POWER/SOFT
TIMER
CLOCK
LIGHT
SET SLEEP
1
Air Purifying Filter (inside)
Outlet
(inside)
(Lights up when unit starts.)
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
will increase

Remote controller

10
1
6
2
7
8
5
9
3
4
HEALTH ON/OFF
23
24
11
13
FAN
18
MODE
15
SWING
POWER/SOFT
23
TIMER
12
20
CLOCK 14
21
LIGHT
19
16
SET SLEEP
17
22
LOCK RESET
1. Mode display
AUTO
COOL
DRY
HEAT
FAN
2. SWING display
3. FAN SPEED display
AUTO LO MED HI
4. SLEEP display
5. LOCK display
6. SIGNAL SENDING
7. TIMER OFF display
NOTE:
Cooling only unit do not have displays and functions related with heating
If the unit which you purchased has healthy function,follow it.If not,please ignore.

Loading of the battery

Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte ries have been used up. Please change batteries.
If the remote controller can't run normally during operation,
please remove the batteries and
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
8. TIMER ON display
9. CLOCK display
10. TEMP display
11. POWER ON/OFF
Used for unit start and stop.
12. MODE
Used to select AUTO run, COOL,
DRY HEAT and FAN operation.
13. FAN
Used to select fan speed LO,
MED, HI, AUTO
14. HOUR
Used to set clock and timer setting.
15. SWING
Used to set auto fan direction.
16. SLEEP
Used to select sleep mode.
17. LOCK
Used to lock buttons and LCD display.
18. TEMP.SETTING
Used to select your desired temp.
19. SET / LIGHT
Used to confirm timer and clock
settings.Control the lightening and
extinguishing of the indoor LED
display board.
20. TIMER
Used to select TIMER ON,
TIMER OFF,TIMER ON-OFF
21. CLOCK Used to set correct time
22. RESET
Used to reset the controller back
to normal condition.
23. HOUR / POWER/SOFT
Used to set clock and timer setting.
Every time the button is pressed,
display changes as follows:
BLANK
POWER SOFT
24. HEALTH
Used to operate the healthy
function and LCD display.
Remove the battery cover;
Load the batteries as
illustrated. 2 R-03 batteries,
resetting key(cylinder);
Be sure that the loading
is in line with the " + "/"-";
reload several minutes later.