BMPRO SwayControl Owner's Manual
Hide thumbs Also See for SwayControl:

Advertisement

Quick Links

OWNER'S MANUAL
SwayControl
TEAMBMPRO.COM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SwayControl and is the answer not in the manual?

Questions and answers

Summary of Contents for BMPRO SwayControl

  • Page 1 OWNER’S MANUAL SwayControl TEAMBMPRO.COM...
  • Page 2: Table Of Contents

    CONTENTS ABOUT THE SWAYCONTROL ....3 COMPATIBLE BRAKE CONTROLLERS � � � � � � � � � � � � � � � � 3 ASYMMETRIC VS SYMMETRIC SWAY CONTROL.
  • Page 3: About The Swaycontrol

    SwayControl will shut itself off� The SwayControl "wakes up" when it receives a brake controller signal and is immediately ready to begin monitoring and controlling trailer sway� When the SwayControl is in "sleep mode", the current draw from the battery is 35mA ±2%� COMPATIBLE BRAKE CONTROLLERS...
  • Page 4: Asymmetric Vs Symmetric Sway Control

    ASYMMETRIC VS SYMMETRIC SWAY CONTROL The SwayControl is an asymmetric sway control braking system� In the event of a sway, the SwayControl will apply both brakes asymmetrically to directly counter the active caravan/trailer sway� Applying both brakes assymetrically directly reduces sway in a way that allows for faster control with minimal speed reduction�...
  • Page 5: Asymmetric Sway

    ASYMMETRIC SWAY SYMMETRIC SWAY TORQUE FORCE FORCE km/h km/h TORQUE FORCE km/h km/h km/h km/h km/h km/h...
  • Page 6: Installation Instructions

    To operate correctly, the SwayControl must be securely fastened using all four mounting holes hard up against the floor of a steel trailer� Do not fasten the SwayControl to any other trailer surface that flexes or moves from wind or road vibration�...
  • Page 7: Mounting

    It is recommended that starlock washers are used and that mounting screws are securely tightened to hold the SwayControl firmly in position and to avoid becoming loose from vibration� WARNING DO NOT drill holes in the SwayControl for any reason� Drilling holes or puncturing the unit will void your warranty�...
  • Page 8 The centre of the SwayControl (marked by the orange dot on the SwayControl label) must be positioned over the centre line of the caravan/trailer� The bottom edge of the SwayControl (as indicated by the orange line on the bottom of the SwayControl label) must be mounted parallel to the trailer beam...
  • Page 9: Wiring Instructions

    WIRING INSTRUCTIONS SWAYCONTROL WIRING HARNESS The SwayControl wire harness has five wires requiring electrical connection and one cable for the status LED light� When making connections to the caravan/trailer’s wiring harness, the desired termination is a solder joint� If the connection is not soldered, use the appropriate size and type of “crimp-type”...
  • Page 10 WARNING When inspecting caravan/trailer wiring, it is very important that the caravan/trailer BLUE brake controller wire from the tow vehicle (blue wire) is ONLY connected to the wire on the SwayControl AND NOT connected directly to the caravan/trailer brakes�...
  • Page 11: Wiring Diagram

    WIRING DIAGRAM...
  • Page 12 Failure to properly connect these wires will prevent the SwayControl from controlling caravan/trailer sway� Remove any old brake wires� Only use the new wire from the SwayControl� WARNING If old brake wires are not removed, the SwayControl may not work as intended�...
  • Page 13: Final Brake Wiring Check And Start Up

    After performing the final brake wiring check, the SwayControl is ready for start-up� WARNING Ensure that SwayControl unit is only activated through the use of a brake controller or a similar PWM device� DO NOT apply direct voltage to the SwayControl until activated through the above method�...
  • Page 14: Status Light Module Installation

    GREEN light will remain on and flicker or pulse� If the SwayControl detects a fault in the system, the Status Light will turn and the fault may be diagnosed from the Status Light flash sequence� The SwayControl continues checking the fault status and the Status Light will continue to flash until the fault is corrected�...
  • Page 15: Status Light Led Indicators

    Correct the short in right side brake flashes Right side brake short wiring Check quality of power and ground Fast flashing Low voltage, between 3 and 6V connections If a service centre repair is required, please contact your BMPRO SwayControl Authorised Repair Centre�...
  • Page 16: Servicing

    Do not attempt to service the SwayControl yourself, OR dismantle, modify or repair the SwayControl yourself; this will void your warranty� The SwayControl unit is a fully sealed unit and has no serviceable parts on the inside� If your SwayControl requires servicing, please consult your BMPRO dealer or...
  • Page 17: Specifications

    SPECIFICATIONS SWAYCONTROL System Voltage 12 - 15V Power Source Caravan/trailer house battery Current Draw (Sleep Mode) 35mA ± 2% Sleep Mode After 30 minutes of inactivity Current Draw (Sleep Mode) 35mA ± 2% Wake-up Mode Brake controller signal Preprogramming Auto System Disable (ASD)
  • Page 18: Warranty Terms And Conditions

    The warranty period of the product is two years� If, before the warranty period has ended, a fault occurs with the product and BMPRO finds the product is defective in materials or workmanship, BMPRO at its discretion will subject to further rights accorded by the Australian Consumer Law to either: • ...
  • Page 19 (k) the fault is a result of common wear & tear� LIMITATIONS No express warranties or representations are made by BMPRO other than what is set out in this warranty� The absolute limit of BMPRO’s liability under this express warranty is the repair or replacement of the product or part of the product�...
  • Page 20 BMPRO TEAM customerservice@teambmpro.com BMPRO 19 Henderson Rd, Knoxfield VIC 3180 Australia .COM teambmpro.com...

Table of Contents