INDEX CONTENTS 1. IMPORTANT SAFETY PRECAUTIONS 2. SYMBOLS 3. ASSEMBLY INSTRUCTIONS 4. OPERATING INSTRUCTIONS 5. INFORMATION FOR USAGE 6. CLEAN UP AND STORAGE 7. TECHNICAL SPECIFICATIONS 8. TROUBLESHOOTING 9. EXPLODED VIEW AND SPARE PART LIST 10. WARRANTY...
IMPORTANT SAFETY TIPS • Never point the high pressure nozzle at people or animals. • Never drink alcohol or use drugs while operating the pressure washer. • Never operate the pressure washer while standing in water. • Never touch the electrical plug with wet hands. •...
Page 6
at yourself or others to clean clothing or footwear. • Disconnect the power supply before carrying out maintenance by the user. • High pressure washers must not be operated by children or unskilled persons. • To ensure machine safety, only original spare parts from the manufacturer or spare parts approved by the manufacturer should be used.
• It is recommended that the electric supply to this machine should include either a residual current device that will interrupt the supply if the leakage current to earth exceeds 30 mA for 30 ms or a device that will prove the earth circuit. WARNING! Do not use the machine within range of persons unless they wear protective clothing.
Page 8
Leaking hoses and fi ings are also capable of causing injection injury. Do not hold hoses or fi ings. To reduce the risk of injury from kickback, hold the spray lance securely with both hands when the machine is on. Failure to use in dry conditions and to observe safe practices can result in electric shock.
• Remove the plug from the socket-outlet during cleaning or maintenance and when replacing parts or converting the machine to another function. PROPER USE OF THE PRESSURE WASHER This unit is intended for use with cold water only! Do not use hot water in this pressure washer. •...
Page 10
STEP 1 Insert the adjustable spray nozzle (7) into the gun (6). Push and turn the adjustable nozzle clockwise onto the gun (6) until hand tight to lock it in place. When the pieces are joined properly, you can not separate the two components by pulling straight out on the adjustable nozzle.
Page 11
STEP 5 Screw the quick connector and filter (8) onto the water inlet pipe. (Fig. 3) A ach the hose joint (2) to the both end of the inlet water hose (1), then connect the inlet water hose (1) (min. hose diameter 13 mm) to the water tap joint (3) and machine. (Fig. 4-6) CAUTION: Prior to a ach the quick connector to machine, check that filter is mounted in the water inlet and that is not blocked up.
4. OPERATING INSTRUCTIONS WARNING: This unit is intended to be used with cold water only! Do not use hot water in this pressure washer! WARNING: High pressure hose must not loop. STARTING UP WARNING: Always turn o the unit's motor before turning o the unit's water supply. Serious damage could occur to the motor if the unit is run without water.
Page 13
When not using the pressure washer, press the lock bu on to keep from accidentally engaging the high pressure spray. Lock Unlock HOLD THE GUN Whenever you use the high pressure washer, we suggest you grip the in the right position, with one hand on the handle and the other on the adjustable spray nozzle.
Page 14
ADJUSTABLE SPRAY NOZZLE The adjustable nozzle will allow you to use any variety of spray pa erns from a full fan spray (diagram 1) to a direct stream spray (diagram 2). When using the pressure washer to clean wood decks, siding, vehicles etc., always start using the fan spray and begin spraying from a minimum 36"...
CLEANING PIN INSTRUCTION Using included nozzle cleaner tool, insert wire into the nozzle hole and move back and forth until debris is dislodged. 6. CLEAN UP AND STORAGE Shu ing down the pressure washer. When finished using the pressure washer, follow these steps to shut down the unit: •...
MAINTENANCE • This pressure washer is supplied with a closed lubrication system, so no addition of oil is needed. • Check all hoses and accessories for damage prior to use. • Check the inlet filter periodically for deposits. Clean this filter regularly for maximum performance. CLEANING TIPS WARNING: Always test the spray in an area free and clear of people and objects before you sprayat the intended cleaning surface.
8. TROUBLESHOOTING WHEN THE SWITCH IS IN THE “ON” POSITION THE MACHINE WILL NOT START. PROBABLE CAUSE SOLUTION Electrical socket is faulty. Check plug, socket, fuses. Voltage is inadequate. Check whether the voltage is adequate. Power cord is not plugged in. Plug in power cord.
WARRANTY Product model Date of sale Company Serial number Client's signature Username Please read and agree to the terms of the warranty. The manufacturer warrants the product against faulty materials and workmanship for a period of 1 year from the date of first purchase to the original purchaser. The warranty is applicable when the product is used in a “home owner”...
Need help?
Do you have a question about the eZX110-1600 and is the answer not in the manual?
Questions and answers