Subscribe to Our Youtube Channel
Related Manuals for Dahua DH-IPC-HDW8341XN-3D-S2
Summary of Contents for Dahua DH-IPC-HDW8341XN-3D-S2
- Page 1 Stereo Vision Network Camera Quick Start Guide V1.0.1 ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD.
-
Page 2: Foreword
Foreword General This manual introduces the functions and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. - Page 3 All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners. Please visit our website, contact the supplier or customer service if there is any problem occurred when using the device. ...
-
Page 4: Important Safeguards And Warnings
Important Safeguards and Warnings Electrical safety All installation and operation should conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited power Source requirement according to IEC60950-1. - Page 5 It is recommended to use the device together with lightning arrester to improve lightning protection effect. It is recommended connect the grounding hole to the ground to enhance the reliability of the device. Do not touch the image sensor (CMOS) directly. Dust and dirt could be removed with air blower, or you can wipe the lens gently with soft cloth that moistened with alcohol.
-
Page 6: Table Of Contents
Table of Contents Foreword ..............................I Important Safeguards and Warnings ....................III 1 Introduction ............................1 Cable ............................. 1 Connecting Alarm Input/output ..................... 2 2 Network Configuration.......................... 4 Initializing Device .......................... 4 Modifying Device IP Address ......................5 Logging in to Web Interface ......................6 3 Installation .............................. -
Page 7: Introduction
Introduction Cable Cable type might vary with different devices, and the actual product shall prevail. Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see the FAQ Manual. Figure 1-1 Cable list For more information about cable ports, see Table 1-1. -
Page 8: Connecting Alarm Input/Output
No. Port Name Description Connects to network with network cable. Provides power to the device with PoE. Ethernet PoE is available on select models. Audio input RCA port. Connects to sound pickup to receive audio signal. Audio output RCA port. - Page 9 Figure 1-2 Alarm input Step 2 Connect alarm output device to the alarm output end of the I/O port. The alarm output is relay switch output, which can only connect to NO alarm devices. N1 and C1 or N2 and C2 constitute a switch to provide the alarm output, which is shown in Figure 1-3.
-
Page 10: Network Configuration
Network Configuration Device initialization and IP setting can be finished with the "ConfigTool" or in web interface. For more information, see the Web Operation Manual. Device initialization is available on select models, and it is required at first use and after device is being reset. -
Page 11: Modifying Device Ip Address
The Device initialization interface is displayed. Step 6 Select the devices that need initialization, and then click initialize. The password setting interface is displayed. See Figure 2-2. Figure 2-2 Password setting interface Step 7 Set and confirm the password of the devices, and then enter a valid email address. Click Next. -
Page 12: Logging In To Web Interface
After clicking Search setting, enter the username and password, and make sure that they are the same as what you set during initialization; otherwise there will be wrong password notice. Step 2 Select the devices whose IP addresses need to be modified, and then click Modify IP. The Modify IP Address interface is displayed. - Page 13 Figure 2-4 Main interface Network Configuration 7...
-
Page 14: Installation
Installation Packing List The tool required for the installation such as electric drill is not provided in the package. The operation manual and related tool are contained in the disk or the QR code, and the actual packing shall prevail. Dimensions The following figures are for reference only, and the actual product shall prevail. -
Page 15: Installing Device
Installing Device 3.3.1 Installation Method 3.3.2 Installing SD Card (Optional) Disconnect the power before installing or removing the SD card. It can connect to TV monitor through the second video port and check image. Installation 9... -
Page 16: Attaching Device
Press the reset button for 10 seconds to reset the device. 3.3.3 Attaching Device You can install the camera through the mounting plate, and install it directly without the mounting plate. Make sure the mounting surface is strong enough to hold at least 3 times total weight of the device and bracket. - Page 17 Cable going through wall Cable going through side cable tray Installation 11...
-
Page 18: Installing Waterproof Connector
3.3.4 Installing Waterproof Connector This part is needed only when there is waterproof connector in the package and the device is used outdoors. 3.3.5 Adjusting Angle Installation 12... - Page 19 ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. Address: No.1199, Bin'an Road, Binjiang District, Hangzhou, P.R. China Postcode: 310053 Tel: +86-571-87688883 Fax: +86-571-87688815 Email: overseas@dahuatech.com Website: www.dahuasecurity.com...
Need help?
Do you have a question about the DH-IPC-HDW8341XN-3D-S2 and is the answer not in the manual?
Questions and answers