Advertisement
This instruction manual contains important information necessary for the proper assembly and safe use of the appliance.
Read and follow all warnings and instructions before assembling and using the appliance.
Follow all warnings and instructions when using the appliance.
Keep this manual for future reference.
Indicates a hazardous situation that, if not avoided, will result in death or serious injury.
Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
NOTICE
Indicates information considered important, but not hazard-related (e.g. messages related to property damage).
If you smell gas:
Failure to follow these instructions could result in fire or property damage, personal injury or death.
Failure to follow these instructions could result in fire or property damage, personal injury or death.
DO NOT USE FOR PURPOSES OTHER THAN INTENDED:
THIS APPLIANCE SHALL BE USED OUTDOORS ONLY.
MAINTAIN PROPER CLEARANCES FROM COMBUSTIBLE MATERIAL:
INSTALLATION MUST CONFORM WITH LOCAL CODES
In the absence of local codes, installation must conform with:
Find a large, clean area to assemble your appliance Remove all packing material before assembling.
Sharp edges. Wear gloves while assembling.
NOT INCLUDED:
LPG cylinder
Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g) size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)
TOOLS NEEDED:
Phillips head screwdriver & Adjustable wrench.
STEP 01
Remove the griddle body from the packaging Push the griddle top forward to unlock the pins from the 4 holes set the griddle top and hood aside.
STEP 02
Place the griddle body upside down Remove the eight (8)
M6x12 bolts on the griddle body and set aside.
STEP 03
Remove the stand from the packaging and use the (8) M6x12 bolts (removed during step 2) to attach the legs to the bottom of the griddle body.
STEP 04
Open the stand legs (When the legs are fully opened, the locking pins will engage To close the legs, pull the locking pins)
STEP 05
Loosen the thumbscrews on the stand legs, then extend the four leg extensions in the stand legs Adjust each leg extension to desired height, then tighten the thumbscrew to secure.
STEP 06
Place the gridle upright loosen the four (4) bolts on the right side of the griddle body, then hang the side shelf on the bolts and press down to lock the shelf in place Retighten the bolts to keep the side shelf stable.
STEP 07
Ensure that the ignition needle is set 3-7mm above the burner tube.
STEP 08
Place the griddle top on the main body by aligning the 4 pins.
Make sure the front pins are fully seated in the holes, then push the griddle top back to lock the griddle in place.
STEP 09
Use the two (2) M6 screws and grommets pre-installed in the handle to install the handle to the front of the hood.
STEP 10
Hang the grease cup in the slot on the back of the griddle body.
STEP 11
Proceed to USING YOUR BLACKSTONE.
NOTICE
DO NOT leave the hood closed for more than 10 minutes while cooking.
NOTICE
1 LB (453 G)
STEP 01
Screw in the LPG cylinder into the gas regulator, turning the cylinder clockwise
The regulator may make a humming or whistling noise during operation. This will not affect safety or use of the appliance.
Cross threading can occur if you force thread a connection at an improper angle. This will damage the threads, lead to propane leaking, and potentially result in a build-up of fuel that can ignite.
DO NOT cross thread the connection between your LPG cylinder and regulator or regulator and gas rail.
If you can not connect the regulator, DO NOT use the regulator.
Regulator must be replaced with a Blackstone approved model by a professionally licensed, authorized dealer.
Use this appliance, as purchased, only with gas and regulator/valve assembly supplied.
If regulator fails in unit, it must be replaced with a Blackstone approved model (found on your Manufacturer label) by a professionally licensed, authorized dealer. Failure to comply will void the warranty.
STEP 02
Insert the regulator and LPG cylinder into the gas line of the appliance Turn the collar of the regulator clockwise to secure it to the gas line.
Always keep new LPG cylinders in upright position during use, transit or storage.
Ensure that the LPG cylinder is positioned below the regulator. (If the liquid level of the propane is above the regulator, the regulator will frost.) (If the liquid level of the propane is above the regulator, the regulator will frost.)
IF FROSTING PERSISTS AFTER BOTTLE IS ANGLED CORRECTLY:
STEP 01
Turn OFF the appliance and disconnect LPG cylinder immediately. This indicates a problem with the LPG cylinder and it should not be used on any.
This indicates a problem with the LPG cylinder and it should not be used on any product. product.
STEP 02
Return LPG cylinder to supplier.
NOTICE
STEP 01
Turn the control knobs to OFF.
STEP 02
Connect the LPG cylinder to the regulator Connect the regulator to the appliance.
The regulator may make a humming or whistling noise during operation. This will not affect safety or use of the appliance.
STEP 03
Brush soapy solution onto joint areas of valves and regulator.
Leaks are indicated by growing bubbles.
STEP 04
If growing bubbles appear, re-tighten connections.
NOTICE
Soap will ruin a seasoned griddle. This is the only time you should use soap on the griddle cooking surface.
STEP 01
Wash the griddle cooking surface with hot, soapy water.
STEP 02
Rinse and dry completely.
STEP 01
Turn knob to OFF position.
STEP 02
Push in knob and release Knob should spring back.
If knobs DO NOT spring back, replace valve assembly before using appliance.
STEP 03
Rotate knob to LOW then turn back to OFF Knob should turn smoothly.
DO NOT lean over the appliance while lighting.
Always check burner flame before use
STEP 01
Light burners and rotate knobs from HIGH to LOW.
STEP 02
Look below the cooking top to view burners.
When knob is at HIGH, flames should be larger than when knob is at LOW.
HEALTHY BURNER FLAME PATTERN
BURNER FLAMES ARE YELLOW OR IRREGULAR
If there is a sudden drop or low flame issue, please reference the Troubleshooting chapter.
WHAT OIL IS BEST TO USE?
VIDEO TUTORIAL
How to season a New Blackstone Griddle
youtube.com/watch?v=VspmdVnj2pI&t=3s
STEP 01
Wipe any debris OFF griddle top.
STEP 02
Set your griddle to high heat until your griddle top changes color. (~10 min)
STEP 03
Use tongs to hold a paper towel or cotton cloth and spread 2-3 tablespoons of your seasoning oil across the entire griddle top.
When seasoning your griddle top, remember to use a thin and even layer of oil — the thinner the layer of oil, the easier it will be to burn it OFF.
STEP 04
The griddle top is ready for another layer of oil when it stops smoking Repeat STEP 03 3-4 times, or until the griddle surface is black.
THERE IS A BROWNISH RESIDUE ON THE GRIDDLE SURFACE:
POSSIBLE CAUSES | SOLUTION |
| STEP 01 STEP 02 STEP 03 |
THE EDGES OF THE GRIDDLE SURFACE ARE NOT BLACK:
After using your griddle for multiple cooks, the seasoning will even out and improve
Use your griddle frequently every time you cook, you are adding to the seasoning, which makes rust less likely.
NOTICE
If you live in a humid or coastal climate, your griddle may require more frequent seasonings between uses.
If rust appears on the griddle surface, rub it OFF with steel wool, LOW grit sandpaper or the Blackstone Pumice Stone and re-season the surface.
VIDEO TUTORIAL
Recovering your Blackstone Griddle Top
youtube.com/watch?v=thPe2IgnsiI
Flammable items can spontaneously combust if placed near the appliance. DO NOT place flammable items such as aerosol containers, oily or greasy towels near the cooking surface.
This appliance will be hot during and after use. DO NOT handle hot parts with unprotected hands. Use long-handled cooking utensils and oven mitts.
NOTICE
DO NOT store any items within 3 in (8 cm) of the cooking surface while in use.
IF GREASE OR OTHER HOT MATERIAL DRIPS ONTO VALVE, HOSE OR REGULATOR:
STEP 01
Turn OFF gas supply immediately.
STEP 02
Determine the cause and correct it.
STEP 03
Clean and inspect valve, hose and regulator.
STEP 04
Perform a leak test (Please reference the leak Test Instructions in USING YOUR BLACKSTONE).
Find recipes and cooking tips at:
BlackstoneProducts.com/blogs/recipes
youtube.com/c/BlackstoneGriddles
@blackstoneproducts
Clean your appliance after each use, after it is cool to the touch
Grease build up can cause a fire. Clean any part of the appliance that gets hot and experiences grease build up after each use.
PLASTIC PARTS & PAINTED SURFACES:
Wash with warm soapy water and wipe dry with a non-abrasive cloth.
NOTICE
DO NOT use Citrisol, abrasive cleaners, or a concentrated cleaner on plastic parts. This may result in damage to and failure of parts.
FOR EVERY SURFACE
The Blackstone de-greaser and Cleaning Spray is gentle enough to clean every surface of your appliance Use it on the cooking surface, the appliance frame, or anywhere that experiences a build up of grease.
DO NOT move the appliance when in use. Allow the appliance to cool to 115°F (45°C) before moving or storing.
COVER FIT GUIDE
Always cover your appliance when stored outdoors.
To find a cover that will fit your appliance, visit BlackstoneProducts.com/support.
Clean griddle top after each use, while still warm
Grease cup will be hot during and after use. DO NOT remove the grease cup until the griddle has completely cooled.
VIDEO TUTORIAL
How to Clean your Blackstone Griddle
youtube.com/watch?v=-Iedu9z6NPY
STEP 01
Push loose food debris into the grease cup with spatula or straight metal scraper.
STEP 02
Wipe down griddle top with paper towel.
STEP 03
Apply a few tablespoons of water to the griddle surface, then scrape the water and debris into the grease cup (For stuck-on food residue, use a bit of coarse salt).
STEP 04
Wipe again with a paper towel and dry completely.
STEP 05
Apply thin coat of cooking oil to maintain seasoning and protect the griddle top.
1 LB (453 G)
STEP 01
Ensure that the control knob(s) are turned to OFF.
STEP 02
Once the appliance has cooled, disconnect the regulator from the gas line by unscrewing the collar.
STEP 03
Unscrew the LPG cylinder from the regulator.
STEP 04
Place dust cap on LPG cylinder valve outlet whenever cylinder is not in use/
Only install the type of dust cap on cylinder valve outlet that is provided with the cylinder valve. other types of caps or plugs may result in leakage of propane.
BURNER WILL NOT IGNITE:
If ignition does not occur in 5 seconds:
STEP 01
Turn the burner control knob OFF.
STEP 02
Wait 5 minutes.
STEP 03
Repeat the lighting procedure.
If this does not work, to determine the cause, please try to ignite your appliance with a match.
MATCH LIGHTING INSTRUCTIONS
Before beginning, check for gas leaks. Open hood (if applicable).
STEP 01
Turn control knob to OFF position.
STEP 02
Light a match (or long lighter) no shorter than 11 inches long.
STEP 03
Place the flame next to the burner.
STEP 04
Push in and turn the control knob to start gas flowing. ensure burner lights and stays lit.
IF YOU CAN IGNITE YOUR APPLIANCE WITH A MATCH:
POSSIBLE CAUSES | SOLUTION |
Ignitor wire misaligned. | Ensure that the ignition needle is positioned 3-7mm away from the burner tube, and above a burner hole.![]() |
Damage to the ignition system. | Contact customer service for replacement parts. |
IF YOU CAN IGNITE YOUR APPLIANCE WITH A MATCH:
POSSIBLE CAUSES | SOLUTION |
Burner tubes are not receiving fuel. | Clean the burner assembly to remove the obstruction. |
BURNER FLAMES ARE YELLOW OR IRREGULAR:
POSSIBLE CAUSES | SOLUTION |
Obstructions in the burner, gas jets, or fuel rail. | Clean the burner, jets, and gas hose. |
LPG cylinder is empty or low. | Refill or replace the LPG cylinder. |
The regulator's flow limiting device was triggered. | Reset the safety system: STEP 01 STEP 02 STEP 03 |
Regulator stuck in safety position. | Contact customer service for replacement parts. |
A FLAME IS COMING OUT OF THE AIR GATE:
POSSIBLE CAUSES | SOLUTION |
Something is blocking the venturi in the burner. | Clean the burner assembly to remove the obstruction. |
VIDEO TUTORIAL
How to Clean Your Burner Tube
youtube.com/watch?v=xKQTCrFCzf8
STEP 01
Ensure that the gas is turned OFF at control knobs and gas supply Remove the cooking top.
STEP 02
Carefully detach and remove the burner.
STEP 03
Clean the inside of the burner:
STEP 04
Brush entire outer surface of burner to remove grime.
STEP 05
Clean any blocked ports with stiff wire such as an open paper clip.
STEP 06
Carefully replace burners and reattach.
The gas rail fuel nozzle must be reengaged within the burner opening
Visit us online at BlackstoneProducts.com/support for assistance concerning appliance use, replacement parts, or your warranty.
CUSTOMER SERVICE HOURS:
Monday – Friday
7:00 am – 5:00 pm (MST)
ACTIVATE YOUR WARRANTY
TO ENABLE THIS WARRANTY, YOU WILL NEED TO PROVIDE:
The serial Number can be found on your appliance's Manufacturer label
(The Manufacturer label is a large silver sticker found on the body of your appliance.)
Register your appliance at BlackstoneProducts.com/register
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the 1939 and is the answer not in the manual?
Questions and answers