Advertisement
Quick Links
Heat pump Water Heater
Operation and Installation Manual
ELECTRICITE
Model
HP80M8-9
HP110M8-9
HP150M8-9
Please read this manual carefully prior to
your use of this water heater.
The appearance of the water heater given
in this manual is for reference only.
Don't install and use the product outdoors.
Advertisement
Related Manuals for Haier HP80M8-9
Summary of Contents for Haier HP80M8-9
- Page 1 Heat pump Water Heater Operation and Installation Manual ELECTRICITE Model HP80M8-9 HP110M8-9 HP150M8-9 Please read this manual carefully prior to your use of this water heater. The appearance of the water heater given in this manual is for reference only.
-
Page 2: Table Of Contents
9.Faults and protection ......................38 10.Product Fiche ........................39 Dear users of Haier, Thank you for choosing Haier products. Please read this manual carefully and follow the operation and safety instruction to ensure best installation and utilization of the product. - Page 3 4. This product must be installed outdoors 5. This product cannot be discarded or scrapped at will. If necessary, please contact Haier's after-sales team to obtain the correct disposal method. When the product is disposed of, the refrigerant in the system needs to be recovered.
- Page 4 Safety instructions (to be followed at any time) Interpretation of marks and symbols Failure to respect these instructions may lead to serious malfunctions of the device and to risks for the user Instructions with this warning mark shall be strictly followed during operation. They relate to product and body safety of users.
- Page 5 Safety instructions (to be followed at any time) The outlet water temperature Means for disconnection from of a water heater is typically the main supply having a higher than the temperature contact separation in all poles indicated on the display. Hot that provide full...
- Page 6 Safety instructions (to be followed at any time) Rotate the safety valve handle Water heaters shall once a month. The valve equipped with a dedicated works well if there is water power line residual flowing out, otherwise check current circuit breakers. The for blocking and replace the action current...
- Page 7 Safety instructions (to be followed at any time) 1.Ask your dealer or qualified personnel to carry out installation work.Do not attempt to install the product yourself. Improper Installation may result in water leakage, electric shocks, fire or explosion. 2.Keep this manual where the user can easily nd it. 3.Install the product in accordance with the instructions in this installa- tion manual.
- Page 8 Safety instructions (to be followed at any time) 1.Do not install the appliance at any place where there is danger of flammable gas leakage.In the event of a gas leakage, build-up of gas near the appliance may cause a fire to break out. 2.Take adequate steps to prevent the outdoor unit being used as a shelter by small animals.Small animals making contact with electrical parts can cause malfunctions, smoke or fire.
-
Page 9: Safety Instructions
Safety instructions (to be followed at any time) Installation Instructions Electrical Safety Requirements 1. The surrounding conditions (ambient temperature, direct sunlight and rainwater) shall be noticed during electrical wiring, with effective protective measures being taken. 2. Copper wire cable in line with local standards shall be used as the power line and connector wire. - Page 10 Safety instructions (to be followed at any time) Maintenance Site Requirements 1. The maintenance site shall be provided with favorable ventilation and must be flat. Arrangement of the maintenance site inside the basement is not allowed. 2. Welding zone and non-welding zone shall be divided at the maintenance site, and shall be clearly marked.
- Page 11 Safety instructions (to be followed at any time) 4. In case leakage is suspected, the open fire at the site shall be evacuated or be put out. 5. In case welding is required at the leakage position, all the refrigerants shall be recov- ered, or be isolated at a position far from the leak point with a stop valve.
-
Page 12: Instructions On Transportation And Storage
Instructions on transportation and storage 1. During transportation or storage, the heat pump water heater shall be packed in the undamaged package to avoid damage to appearance and performance of the product; 2. During transportation or storage, the heat pump water heater shall be in the upright position;... -
Page 13: Technical Parameters
51/58kg 54/62kg 64/83kg The COP and noise level data was tested in Haier lab. The COP values obtained with external air temperature of 7°C and 14°C, inlet water temperature of 10°C and set temperature of 55°C (according to EN 16147). -
Page 14: Description Of Parts And Components
Description of parts and components Heat pump structure Condensate outlet Inlet for cold Hot water water/drain outlet outlet Air outlet Air inlet Accessories Part Heat pump Instruction Safety Drainage pipe for Support plate name water heater manual condensate water valve 1(HP80M8-9) Quantity 1(HP110M8-9) 2(HP150M8-9) - Page 15 Description of parts and components Exploded view Description Electric cover Electric heater Display panel Cover for display Capacitor for compressor Controller panel Compressor Four-way valve Electronic expansion valve Evaporator Top cover Air grille Air channel - front Motor Air channel - back Support plate Power cord 19 Pipe for water outlet...
-
Page 16: Installation Introduction
Installation introduction Installation precaution - Do not install the water heater in the position where exposed to gas, vapours or dust. - Install the appliance on a flat, solid surface.The surface can support the machine weight and the condensate water can be drained freely. - Noise due to operating and air flow do not bother neighbors. - Page 17 Installation introduction Installation dimensions Unit:mm Model HP80M8-9 1184 HP110M8-9 1334...
- Page 18 Installation introduction Installation dimensions Unit:mm Model 1694 HP150M8-9...
- Page 19 Installation introduction Installation dimensions Note: These two expansion bolts can support 200kg weight at least . Please use the expansion bolts adapted to your wall material. Note： Please dismantle the elbows before removing the top cover. Installation angle refer to the following After the installation is completed, it is necessary diagrams：...
- Page 20 Installation introduction Installation dimensions Note: These two expansion bolts can support 250kg weight at least . Please use the expansion bolts adapted to your wall material. Note： Please dismantle the elbows before removing the top cover. Installation angle refer to the following After the installation is completed, it is necessary diagrams：...
- Page 21 Installation introduction Air connection - Remove air grille first. click y Meter-long x Meter-long φ160mm φ160mm φ160mm Available pressure 30 Pa Drop Equivalent Pressure 1m-long (Pa) Smooth 0.6 /1 meter tube Bellows 1 /1 meter Installation suggestions: x + y < 36 m (Smooth tube) x + y <...
- Page 22 Installation introduction Advised positions Garage or laundry room (without ducts): -Unheated room. -Enables recovery of the free energy released by your vehicle’s engine when switched off after use or by household appliances in operation. Laundry room (with one duct): -Unheated room. -Enables recovery of the free energy released by your vehicle’s engine when switched off...
- Page 23 Installation introduction Installation caution When making the connections, you should respect the standards and local directives. - Before making the connection, rinse the water inlet pipes, in order not to introduce metal or other particles into the tank. - Select copper pipes for pipeline connection. - The inlet water pressure is between 0.1~0.5MPa.
- Page 24 Installation introduction Pipeline installation diagram Installation A Thermostatic valve Check valve 230V 50Hz Hot water outlet Outlet of condensate water Pressure Stop Check valve valve relief valve safety valve Drain valve Water outlet of Cold water inlet safety valve Water outlet Installation B(for France only) Connected to water inlet of the water tank...
- Page 25 Installation introduction Electrical connections precautions WARNING - Only qualified professionals may carry out electrical connections, always with the power off. - The earthing shall comply with local standards. - Water heaters shall be equipped with a dedicated power line and residual current circuit breakers.
- Page 26 Installation introduction Off-peak power signal wire connection 123kwh Auto Off-peak power signal wire (2*0.75mm ,Black wire) Power cable (3*1.5mm...
- Page 27 Installation introduction Wiring diagram Compressor CN11 CN12 Capacitor Four-way Discharge temperature valve CN13 sensor MAIN BOARD CN10 Defrost temperature White sensor ︳ Ambient temperature Brown sensor White Suction temperature sensor ︳ Black Water tank temperature sensor ( upper) Compressor ︳ CN7/8 CN24 Water tank temperature...
-
Page 28: Operation And Functions
Operation and functions Display Menu button Rotary knob Return button Functions & Protections Electrical leakage protection The control system of this machine features an electricity leakage protection function. 3-minutes protection When starting the machine after electricity input, the system will start after approximately 3 minutes ,which is considered to be normal. - Page 29 Description of the icons Symbol Description Current date display 11/18/2022 11:30 Current time display PV/SG/HC signal display Sterilization function display Mute function display WIFI function display Heat pump heating indication Electric auxiliary heating indication Indication of hot water availability Lock function display -Optimised management of the heat pump and backup element for guaranteed comfort ；...
- Page 30 Function Introduction power on 1. When powered on for the first time, all icons will light up for 3 seconds, and the buzzer will beep once to enter the power on state. Enter the initialization settings and select the confirmation language (Chinese/English/French/Italian/German/Spanish/Portuguese/Polish) 、...
- Page 31 Function Introduction Boost function After selecting Boost, press the Rotary knob to confirm and make an ON/OFF selection. After the selection is completed, if the setting is successful, the prompt will indicate successful setting, otherwise the prompt will indicate failed setting.BOOST mode has the highest priority and can be started in any mode．Only valid once.
- Page 32 Function Introduction Mode selection ECO mode After selecting ECO by rotating the button, enter the selection interface, where you can select the ECO time period, such as Same every day - Different every day. ELEC mode After selecting ELEC, press Rotate knob to confirm, and then prompt whether the setting is successful or not.
- Page 33 Function Introduction Mode selection VAC mode After selecting VAC, press the Rotary knob to confirm and enter the start and end time period setting. After the time setting is completed, select the OK button to automatically return to the menu interface. The main interface displays VAC mode. In this mode, the system activates the water tank protection function (anti freezing, etc.) and prepares hot water in advance based on the vacation return date entered by the user.
- Page 34 Function Introduction Accumulated quantity display function After selecting information, press Rotary knob to confirm. After entering the selection interface, there are four types of information that can be queried: Energy Accumulation - Energy consumption - Operation information - Message reset, all selected by rotating the Rotary knob.
- Page 35 Function Introduction Settings After selecting Settings, press the Rotary knob to confirm and enter the selection interface. There are 6 options to choose from, including date, connection, language, temperature, HP, and volume, all of which are selected by rotating the button. Time settings After selecting DATE by rotating the button, the color of the year deepens.
- Page 36 Function Introduction Language settings After selecting LANGUAGE, enter the language selection for a total of 8 languages. After confirmation, it will automatically return to the menu. Target Temperature&Unit Settings After selecting TEMP, you can set the temperature unit and temperature target value. After confirming the selection, return to the main interface.
-
Page 37: Checking And Maintenance
Checking and maintenance Top Cover Removal Remove the screw in the left with a screwdriver; Rotate the top cover counterclockwise until you can take it off. Checking of the main control board Use a screwdriver to remove the screw. Controller panel Display panel Cleaning of the fan - Check the cleanliness of the fan one time per year. -
Page 38: Faults And Protection
Faults and protection Digital Release Fault type Action indication Communication failure between Wi-Fi Communication fault module and control board Operating temperature protection Air exhaust temperature protection Compressor protection After fault is solved, Evaporation high temperature switch on power protection supply for release Compressor over-current Over-current protection protection... -
Page 39: Product Fiche
128.3 190.0 Load profiles of water heaters, Type Qingdao Economic & Technology Development Zone Haier Water-Heater Co.,Ltd. Manufacturer Haier Industry Park, Economic & Technology Development Zone, 266101 Qingdao, Address PEOPLE'S REPUBLIC OF CHINA Heat pump water heater Denomination Hot water... - Page 40 0040512317 20231007 V*****...