Specifications - Advanced Motion Controls FlexPro FE060-60C-CM Quick Start Manual

SPECIFICATIONS

Description
Nominal DC Supply Input Range
DC Supply Input Range
DC Supply Undervoltage
DC Supply Overvoltage
Logic Supply Input Range (required)
Safe Torque Off Voltage (Default)
Minimum Required External Bus Capacitance
Maximum Continuous Current Output
Efficiency at Rated Power
Maximum Continuous Output Power
Maximum Power Dissipation at Rated Power
Minimum Load Inductance (line-to-line)
Switching Frequency
Maximum Output PWM Duty Cycle
Description
Communication Interfaces
Command Sources
Feedback Supported
Commutation Methods
Modes of Operation
Motors Supported
3
Hardware Protection
Programmable Digital Inputs/Outputs
Programmable Analog Inputs/Outputs
Primary I/O Logic Level
Current Loop Sample Time
Velocity Loop Sample Time
Position Loop Sample Time
Maximum Encoder Frequency
Description
Size (H x W x D)
Weight
Ambient Operating Temperature Range
Storage Temperature Range
Relative Humidity
Form Factor
P1 SIGNAL CONNECTOR*
TERMINAL PINS
Notes
1. Continuous A value attainable when RMS Charge-Based Limiting is used.
rms
2. Lower inductance is acceptable for bus voltages well below maximum. Use external inductance to meet requirements.
3. Maximum motor speed for stepper motors is 600 RPM. Consult the hardware installation manual for 2-phase stepper wiring configuration.
4. Additional cooling and/or heatsink may be required to achieve rated performance. Repeated over temperature events may cause damage to the drive due to the drive's
high power density. Ensure that proper thermal management is adhered to during drive operation.
*Mating Connector Kit
Surface mount board connector for P1 and board spacers can be ordered as a kit using ADVANCED Motion Controls'
part number KC-MC1XFE01.
Release Date:
6/12/2024
Electrical Specifications
Units
VDC
VDC
VDC
VDC
VDC
VDC
µF
A (Arms)
1
%
W
W
µH
2
kHz
%
Control Specifications
Units
-
-
-
-
-
-
-
-
-
-
µs
µs
µs
MHz
Mechanical Specifications
Units
mm (in)
g (oz)
°C (°F)
4
°C (°F)
-
-
-
-
ADVANCED Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
12 – 48
10 – 55
8
58
10 – 55
5
500
60 (60)
99
3267
33
150 (@ 48VDC supply); 75 (@24VDC supply); 40 (@12VDC supply)
20
83
CANopen (USB for configuration)
±10 V Analog, Over the Network, Sequencing, Indexing, Jogging, Step
& Direction, Encoder Following
Absolute Encoder (BiSS C-Mode, EnDat 2.2, Tamagawa/Nikon, SSI),
Hall Sensors, Incremental Encoder, Auxiliary Incremental Encoder,
Tachometer (±10V)
Sinusoidal, Trapezoidal
Profile Modes, Cyclic Synchronous Modes, Current, Velocity, Position,
Interpolated Position Mode (PVT)
Three Phase (Brushless Servo), Single Phase (Brushed Servo, Voice Coil,
Inductive Load), Stepper (2- or 3-Phase Closed Loop), AC Induction
(Closed Loop Vector)
40+ Configurable Functions, Over Current, Over Temperature (Drive &
Motor), Over Voltage, Short Circuit (Phase-Phase & Phase-Ground),
Under Voltage
4/3
1/0
5 VDC, not isolated
50
100
100
20 (5 pre-quadrature)
38.1 x 25.4 x 11.5 (1.50 x 1.00 x 0.45)
19.8 (0.7)
0 – 65 (32 – 149)
-40 – 85 (-40 – 185)
0-95%, non-condensing
PCB Mounted
80-pin 0.4mm spaced connector
26x Terminal Pins
FE060-60C-CM
Value
Value
Value
Page 3 of 7