Related Manuals for NEFF T29R96N0AU
Summary of Contents for NEFF T29R96N0AU
- Page 1 This cooktop is for use with Natural Gas and LPG T29R8 N0AU T29R9 6NOAU Neff GmbH ß Carl-Wery-Stra e 34 81739 München Cod. 9 000235447 C...
- Page 2 Although this last solution is far from perfect, your oil will be taken to a controlled refuse dump where it will not be allowed to pollute water. You and your children will appreciate it.
-
Page 3: Table Of Contents
CONTENT Safety considerations For your safety What to do if yo smell gas Warnings Installation Preparing to install Clearances Installation of cooktop into Kitchen bench Installation procedure Connection Electrical connection Gas connection Conversion front Nat. Gas to LPG To change injectors... -
Page 4: Safety Considerations
• Inmediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier , call the fire department. • Installation and service must be performed by an authorised person. - Page 5 10. Important. When using a very large pot, leave a gap of at least 50 mm (2”) to avoid damaging any parts in bench top wood, plastic or other non-heat resistant materials. Never leave oil or hot fat unattended. 11.The surfaces on heating and cooking appliances get hot when in use.
-
Page 6: Installation
These built-in hobs are intended to be install inserted in a benchtop cutout. Only authorised personnel should connect the appliance. Before you begin, turn off the gas and electricity supply. Installation dimensions are shown in Fig.1. Natural gas Pressure test point. Pressure test point... -
Page 7: Clearances
A range hood fitted above the top must be installed according to the installation instructions for the range hood. A minimum distance of 650 mm is required for a range hood and 750 mm for an exhaust fan. Any adjoining wall surface situated within 200mm from the... - Page 8 3. Place the hotplate on top of the bench cut-out and press down firmly on all edges at the same time to ensure that the hob is resting on its entire perimeter. 4 .Once the hob is fitted you should turn the clips and...
-
Page 9: Connection
Installation continued Connection Electrical: An electrical 10 amp socket needs to be within 1 m of the hotplate to allow electrical connection. The socket must remain accessible after installation of the appliance. Important note: This appliance is connected to the mains (240 VAC) by means... -
Page 10: Gas Connection
There are two ways to carry out the connection to the main gas line: A. The hotplate can be connected with rigid pipe as specified in AS5601 table 3.1. B. Flexible Hose: If installing with a hose assembly, install with a hose assembly that complies with AS/NZS 1869 (AGA Approved), 10mm ID, class Bor D, no more than 1,2m long and in accordance with AS5601. -
Page 11: Conversion Front Nat. Gas To Lpg
To change injectors from Nat.Gas to All work involved in installation, setting and adaptation to a different gas type must be carried out by authorised personnel from our Service Centre and must comply with current regulations and the conditions laid down by the local gas company. -
Page 12: Injector Size Chart
Refer Fig.11. Do not remove the interior disk seal. -
Page 13: Operating Instructions
If it does not light, the on display will flash. Turn the switch to the position and repeat the operation. To turn it off, turn the control to the right to the position The display corresponding to the hotplate will flash briefly and then will stay on, indicating high temperatures in the cooking zone. -
Page 14: On And Residual Heat Display
Burner Position Graphic The control knob is used to adjust the flame of the gas burner. “Low flame” graphic= lowest output “High flame” graphic= higest output On and residual heat display Once the cooking zone has been disconnected, the residual heat indicator will remain on indicating that the temperature is too high here. -
Page 15: User Instructions
User Instructions User Instructions Boiling burners Use “High flame” setting to bring the pan to the boil, then adjust the flame between “High flame” and “Low flame” to maintain the required pan temperature. Important: The use of a cooktop leads to the production of heat and moisture in the kitchen .For this reason make sure that... - Page 16 Cooking recommendations Very high /High Medium Wok burner Boiling, grilling, Reheating and keeping browning, and Asian things hot, cooked and food (wok). pre-cooked dishes. Medium Steaming potatoes, Reheating, keeping fresh vegetables, things hot and making burner stews and pasta. tasty casseroles.
-
Page 17: Warnings Concerning Cooking
Only use one recipient per Do not use two burners or burner. Use the extra heat sources for a single metal grid on the wok recipient. burner. Do not use baking trays, earthenware dishes, etc... at full heat for a long time... -
Page 18: Cleaning And Maintenance
Be careful with the feet on the metal grids when cleaning them; if they are detached, Be careful with the feet on the metal grids when cleaning them; if they are detached, Be careful with the feet on the metal grids when cleaning them;... -
Page 19: Service
Yellow tipping of the hob burner flame. Sooting up of cooking utensils. Burners not lighting properly. Burners failing to remain alight. Gas valves, which are dificult to turn in case the appliance fails to operate correctly, contact the authorised service provider in your area. -
Page 20: On Indicators And Fault Messages
On and fault message display... -
Page 21: Wiring Diagram
T29R96NOAU T29R8N0AU 47,6 41,2...