Page 1
Operating, installation and caring instructions T28V56N0...
Page 2
Before you get rid of an old appliance, make sure you render it useless, and then take it to a centre for the recovering recyclable materials. Ask your local authorities for details on the nearest centre to your home.
Page 3
Always, keep children away from the appliance. Very hot fat or oil can easily catch fire, and so if you are cooking with fat or oil keep an eye on the pan. DANGER If a pan containing fat or oil catches fire, do not pour water onto it, as this may cause burns.
Page 4
– risk of short-circuiting. Whenever the appliance is fitted under a vapour extractor hood and the hob is in use, always have pots or pans over the burners in use. With an open flame the vapour extractor hood may become damaged by external heat development or grease residues in the filter may ignite.
Installation (for the installer) ................... 9 Electrical connection..................... 11 Gas connection (for the fitter)................12 Caution ......................... 15 Converting the burners to another type of gas (for the fitter) ....... 16 Changing the nozzles ................... 16 Nozzle table......................17 2. OPERATION ....................18 This is your new hob.....................
Before installing the unit, remove any protective film. When the hob is built in over a cabinet with drawers, the upper drawer has to be replaced with a cabinet front. No installation directly over a drawer!
Page 8
Chimney cooker hoods are to be installed in accordance with the installation instructions of the hood. On the furniture into which the appliance is to be installed, the plastic coating and/or veneer must have been treated with a heat-resistant adhesive, otherwise it may become distorted or peel off, especially on the narrow sides.
50x50 mm. Any eventual cabinet, resting on the worktop, at any of the two sides of the hob, and the upstand on the back of the hob, each must be at least 50 mm from the edge of the hob itself.
III, as per the installation’s regulation. This is not the case if the connection is by means of a plug, provided the user has easy access to the plug itself.
(for the fitter) Attach the elbow coupling to the appliance gas supply, using the seal provided. Your hob is pre-mounted with the connection ISO 7-1. In order to change the elbow coupling (see picture 4) Picture 4...
Page 14
The maximum permissible length of the gas connecting pipe is 2.5 m. IMPORTANT!!! This safety gas tube must be routed in such a way that it is not fed through hot areas and does not come into contact with any hot parts of the appliance, e.g.
It is important to note that we shall accept no liability for damage which is a direct or indirect result of improper connection or installation. The appliance must always be disconnected from the mains before repairs are carried out.
Changing the To see which gas type has been preset in the nozzles factory; refer to the rating plate in this manual or on the underside of the hob. CHANGING THE NOZZLES The burners are adaptable to different types of gas by replacing only the nozzles for the type of gas used (see data table).
REGULATION OF MINIMUM FROM NG TO LPG Nozzle table 1. Light the burner and turn the knob to the minimum position. 2. Remove the knob from the tap 3. Introduce a small screwdriver in hole B (picture 6) and tighten the adjusting screw completely (taking care not to turn the shaft of the tap).
This is your new Auxiliary burner, 1.0 kW Semi - Rapid burner, 1.75 kW Triple Crown Wok burner, 3.5 kW This control is used to make the heat setting of the Gas tap gas burner. "Small flame" = lowest setting "Large flame"...
"large flame". Press the knob down firmly and hold for approx. 3 seconds - only then will the gas be released from the burner and safely ignited by the sparks. When the burner is ignited release the knob.
Warning: • Make sure that pans are always placed centrally on the gas burner and never place the pot directly on the burners. • The pots should not come onto, or in any way, in contact with the countertop.
When using your concave wok pan, please make sure that the wok pan is placed over the wok support, the bottom of the wok pan is not to come in direct contact with the main pan support or burner.
4. CARE AND CLEANING If cared for properly, your gas hob will continue to How to care for look good for a long time, and cleaning will also be your gas hob: easier. Use a sponge and soapy water (or a specialist...
You should only start to clean the burner cap Your burner and once it has cooled to its normal temperature burner cap after use, i.e. when you can touch it with your bare hand. • The burner cap should be cleaned with hot water and a normal cleaning agent, using a soft sponge or cloth.
• Only clean the pan support once it has cooled to Pan support its normal temperature, i.e. when you can touch it with your bare hand. • The pan support can be removed for cleaning. • The pan support should be cleaned with hot...
Page 25
Probable cause Solution wrong? - Defective fuse. - Check the fuse in the main fuse box and change it if necessary. - The automatic fuse may have - Check the main fuse box to see fused or the trip switch has whether the automatic trip switch tripped.
Environmentally-conscious recycling can reclaim valuable raw materials. Before disposing of your old appliance, please make sure that it is unusable, or label it with a sticker stating "Caution, scrap". Up-to-date information on how to dispose of your old appliance and the packaging from the new one can...
Page 27
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal.
Page 28
Service If you should contact our Customer Service, please state E- and FD-number of your gas hob. Neff GmbH Carl-Wery-Str. 34 D-81739 München 02.2009...