Draper 41096 Original Instructions Manual
  1. Manuals
  2. Brands
  3. Draper Manuals
  4. Impact Driver
  5. 41096
  6. Original instructions manual
Draper 41096 Original Instructions Manual

Draper 41096 Original Instructions Manual

1/2” composite impact wrench
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EN
Original Instructions
Version 1
½" COMPOSITE
IMPACT WRENCH
41096

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 41096 and is the answer not in the manual?

Questions and answers

Related Manuals for Draper 41096

Summary of Contents for Draper 41096

  • Page 1 Original Instructions Version 1 ½” COMPOSITE IMPACT WRENCH 41096...

  • Page 2: Copyright © Notice

    All photographs and drawings within this manual are document is part of the product; retain it for the life supplied by Draper Tools to help illustrate correct of the product, passing it on to subsequent holders. operation of the product.

  • Page 3: Table Of Contents

    2. Contents 1. Preface 1.1 Product Reference 1.2 Revisions 1.3  Understanding the Safety Content of This Manual 1.4 Copyright © Notice 2. Contents 3. Product Introduction 3.1 Intended Use 3.2 Specification 4. Health and Safety Information 4.1  Health and Safety Instructions for this Air Impact Wrench 4.2 ...

  • Page 4: Product Introduction

    Always and exceed expectations of the most demanding user. ensure that the correct tool mode is selected. Draper Tools accepts no responsibility for improper use of this WARNING! This product is not a toy and must be product.
  • Page 5 3. Product Introduction Important: The declared vibration total values and noise emissions values have been measured in accordance with a standard test method and may be used for comparing one tool with another. These values may also be used in a preliminary assessment of exposure.

  • Page 6: Health And Safety Information

    • Regularly inspect the impact wrench to ensure that all safety markings remain legible. • Hold the tool correctly and firmly and brace yourself − Contact Draper Tools if the safety markings need   against sudden movements, keeping both hands to be replaced and DO NOT use the tool.
  • Page 7 • Exposure to high noise levels can cause permanent • ONLY use accessory types and sizes recommended by hearing loss and other problems. Draper Tools. − Perform a risk assessment and implement any   • ONLY use sockets and insert bits that are rated for appropriate controls for identified hazards before impact wrenches and are in good condition.

  • Page 8: Additional Safety Instructions For Pneumatic Tools

    − Maintain a firm grip on the tool and brace yourself   • Draper Tools recommends the use of a whip hose appropriately against the torque and any between the tool and the air supply to reduce unexpected reactionary forces exhibited by the vibration.

  • Page 9: Residual Risk

    4. Health and Safety Information • Keep your hands away from the anvil and impact socket during operation as unexpected movements may cause injury. • Secure the workpiece firmly; DO NOT hold it by hand. • Allow the tool to do the work; DO NOT apply additional pressure against the tool.

  • Page 10: Identification And Unpacking

    Please examine it for any signs of damage that may have contact the Draper Helpline; contact details can be occurred during shipment. If any part is damaged or found at the back of this manual.

  • Page 11: Preparation Instructions

    Fig. 1  The compressed air system must be controlled by a When using an air tool with a hose over 25ft long, Draper combination pressure regulator, in-line lubricator and Tools recommends increasing the bore of the hose to the moisture filter. This will ensure a constant supply of dry next largest available size (i.e.

  • Page 12: Connection To The Air Supply

    6.3 Connection to the Air Supply 6.4 Installing and Removing Impact Sockets Important: Draper Tools recommends using a 1/4” BSP male-threaded thread whip hose (Stock No. 54438, not Important: This product must be used with chrome supplied) to connect the spray gun to an air line in order molybdenum impact sockets and inserts ONLY.

  • Page 13: The Rotation Direction Lever

    6. Preparation Instructions 6.5 The Rotation Direction Lever Important: Check the position of the rotation direction switch (6) and ensure that the tool is set to the correct torque before EVERY operation. Over-torquing bolts and fixings may cause them to shatter and damage the workpiece or cause injury.

  • Page 14: Operation Instructions

    7.1 Basic Operation • Draper Tools recommends performing several test Depress the trigger (8) to start the tool. The anvil (3) will operations before each use to familiarise yourself with rotate in the direction selected using the rotation the tool and fastenings.

  • Page 15: Maintenance And Troubleshooting

    8. Maintenance and Troubleshooting 8.2 Storing the Tool Important: ALWAYS ensure that the air supply is disconnected from the tool before performing any • Disconnect the air line and remove the air line maintenance or storing the product. coupling or whip hose when storing the product. 8.1 General Maintenance Important: Lubricate the mechanism by pouring a few drops of air tool oil into the air line coupling and...

  • Page 16: Troubleshooting

    Replace the o-ring seal or contact Draper broken or dislodged. Tools for support. The trigger valve stem is bent or Lubricate the trigger with air tool jammed with dirt. lubricating oil. If the issue cannot be resolved, contact Draper Tools for support. – 16 –...

  • Page 17: Spares, Returns And Disposal

    Draper Tools Product Helpline for details of your nearest authorised agent. Draper Tools will endeavour to hold any spare parts, if applicable, for seven years from the date that it sells the final matching stock item.

  • Page 18: Warranty

    This warranty period covers parts and labour for 12 months from the date of Your Draper Tools guarantee is not effective until you can purchase. Where tools have been hired out, the warranty produce, upon request, a dated receipt or invoice to period covers 90 days from the date of purchase.

  • Page 19: Explanation Of Symbols

    11. Explanation of Symbols Read the instruction manual Max. air pressure psi Warning! Max. air pressure bar Do not abandon in the environment Average air consumption cfm Wear suitable protective goggles Average air consumption L/min L/min 3/8" Wear ear defenders Min.
  • Page 20 Telephone Sales Desk: +44 (0) 23 8049 4333 General Enquiries: +44 (0) 23 8026 6355 General Fax: +44 (0) 23 8026 0784 Please contact the Draper Tools Product Helpline for repair and servicing enquiries. © Published by Draper Tools Limited © Published by Draper Tools Limited...

Table of Contents