Advertisement
Basic System Configuration
Sensors
Z510-SW2T (0.5-m cable)
Z510-SW6 (0.5-m cable)
Z510-SW17 (0.5-m cable)
Sensor Extension Cables
Z519-SCIR (1.5 m, 3 m, 6 m, 8 m, 13 m, or 18 m)
Specify the required cable length when ordering.
Up to 2 Sensors can be connected.
Specifications
Controllers:
Z510-WC10E and Z510-WC15E
General Specifications
Item
Supply voltage
21.6 to 26.4 VDC
Current
1 A max. (with 2 Sensors connected)
consumption
20 MΩ min. (at 100 V DC) between DC exter-
Insulation
nal terminals and GR terminal
resistance
(with internal surge absorber removed)
1,000 VAC, 50/60 Hz between DC external ter-
Dielectric
minals and GR terminal (with internal surge
strength
absorber removed)
Leakage current
10 mA max.
1,500 V
P-P
Noise resistance
edge: 1-ns pulse
10 to 150 Hz (double amplitude of 0.1 mm)
Vibration
for 8 minutes each in the X, Y, and Z direc-
resistance
tions
2
Shock resistance 200 m/s
3 times each in 6 directions
Operating: 0 to 50° C (with no icing or con-
densation)
Ambient
temperature
Storage: -15 to 60° C (with no icing or con-
densation)
Ambient
Operating and storage: 35% to 85% (with no
condensation)
humidity
Atmosphere
No corrosive gases
Less than 100 Ω
Grounding
Degree of
IEC60529 IP20 (In-panel)
protection
Material
Case: ABS
B-54
Controllers
Z510-WC10E
Z510-WC15E
Specification
; pulse width: 0.1 µs/1 µs; rising
Power supply
F150-VM
Monitor Cable (2 m)
BNC Jack
(Included with the F150-VM)
Characteristics
Item
Number of Sensors Up to 2 Sensors can be connected.
Number of scenes
16
Automatic (The light intensity tracking
Light intensity
range can be specified.)
tracking function
Fixed (Select one of 31 stages.)
Select one of the following 6 items:
Measurement
Deviation from reference surface, Bead
items
height, Width, Bead change, Peak/Bottom,
Inspection length
Region
A region can be specified in the direction of
the line beam.
specification
Data storage
2,048 points max.
Trigger function
Free-run, External 1, External 2, or Auto
• Judgement output
• Measurement value output
Results output
(measurement value)
8 input points: TRIGGER, LD-OFF, RE-
Terminal block
12 output points:DO0 to DO5, DO8, DO15,
Monitor interface
1 channel (for pin jack or overscan monitor)
The full-scale output can be divided into
40,000 gradations max.
Analog output
resolution
Resolution (See note.): 0.25 mV (± 5 V)
0.4 µA (4 to 20 mA)
Weight
Approx. 700 g (Controller only)
Note: This resolution is for measurements with an OMRON K3AS Linear Sen-
sor Controller connected and values averaged over 64 measurements.
Displacement sensors / Width-measuring Sensors
Console
Z300-KP
(2-m cable)
ESC
TRIG
ENT
SHIFT
CONSOLE
Monitors
F150-M05L
Color Liquid Crystal Monitor
(pin input)
POWER
SYNC
Use the Monitor to check
the image and display
menus when making
Specification
RS-232C output
Terminal block output
RS-232C output
Analog output
SET, DI0, and DI4 to DI7
DO17 to DO19, and GATE
Advertisement
