Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MODE KS Series
Summary of Contents for MODE KS Series
- Page 1 KS-Series GAS FIREPLACE User Guide INCLUDING SMARTHEAT APP INSTRUCTIONS 630745_0...
- Page 2 WARNING: IF THE ELECTRICAL CORD IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER, ITS SERVICE AGENT OR SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A HAZARD. THE DATA LABEL FOR THIS APPLIANCE, CONTAINING TECHNICAL INFORMATION AND SPECIFICATIONS, CAN BE FOUND ADHERED TO THE METAL WORK UNDER THE GAS TRAY.
-
Page 3: Table Of Contents
CONTENTS A Remote Control Layout B Basic Operation B1 Activating the Remote (first time use) B2 Charging the Remote B3 Initial Start B4 Adjusting the Room Temperature B5 Fan Boost B6 Flame Effect C Timer Operation D Auxiliary On/Off Button E Over Temp Shutoff Operation F Changing Temperature UNIT (°C to °F) G Sound and Smell G1 Sounds G2 Fan G3 Gas Control Valve G4 Appliance Metalwork G5 Smells H Trim/Fascia and Glass care... -
Page 4: A Remote Control Layout
REMOTE CONTROL L AYOUT Power Bu�on Touchscreen Menu USB-C Charge Port 630745 MODE SERIES USER GUIDE... -
Page 5: B Basic Operation
BA SIC OPER AT ION B1 Activating the Remote (first time use) The remote arrives in a locked shipping state. To unlock it, please plug it into power via the USB-C port for 1 second. Note: The remote does not come with a charging cable. B2 Charging the Remote Charge the remote through the USB-C port in the bottom of the remote using a USB-C cable. -
Page 6: B4 Adjusting The Room Temperature
FAN BOOST toggle button will increase the fan speed to its maximum and help transfer the maximum amount hot air form the fire into the room. When this mode is not on, the fire will still use fan speeds one, two, and three. -
Page 7: C Timer Operation
T IMER OPER AT ION Timers are only created by using the Escea Smartheat APP and then are stored on the fire. In order for the timers to work, the fire needs to understand local time. Therefore the fire must be connected to the Internet in order for the timers to operate correctly. -
Page 8: E Over Temp Shutoff Operation
(Pilot). All burners restart when the room cools down again. This feature is called "Overtemp Shut Off Mode." To activate this mode and make the fire turn off all burners when the room gets too warm, follow these steps: Go to the advanced options on your remote and toggle the "Overtemp" button. -
Page 9: G Sound And Smell
S OUND AND SMELL G1 Sounds It is possible that you will hear some sounds from your gas appliance. This is perfectly normal due to the fact that there are various types of materials used within your appliance. Listed below are some examples. These are all normal operating sounds and should not be considered as defects in your appliance. -
Page 10: H Trim/Fascia And Glass Care
T RIM/FA S C IA AND GL A S S C ARE H1 Powder-coated Trim Care The Trim is the visible surround of your Mode Gas Fireplace and must be treated carefully to prevent unsightly marks from tarnishing the visual quality of the product. -
Page 11: J Power Failure
If the remote was turned off after the power cut then the fire will return to standby mode once the electrical supply is restored until its next use. If however the remote was left in the on mode then the fire will relight... -
Page 12: K Escea Smartheat App
Also if for any chance the fire is unable to be located, contact Escea with the serial number of the fire. ͳ Once the fireplace has been found, you can pair this to your device by entering the PIN found within the 630745 MODE SERIES USER GUIDE... -
Page 13: K3 Connecting An Escea Fire To Wi-Fi
settings menu on the remote control or the information card supplied within the remote packaging. ͳ After a fire is paired against the mobile device, that mobile device automatically becomes a smartheat enabled controller via the app. As a smartheat controller, the mobile device will communicate with the fire via Bluetooth while it is in range (typically within the house). -
Page 14: K4 Basic App Functionality
ͳ If your Bluetooth devices won't connect, it's likely because the devices are out of range, or aren't in pairing mode. If you're having persistent Bluetooth connection problems, try resetting your devices, or having your phone or tablet "forget" the connection.
Need help?
Do you have a question about the KS Series and is the answer not in the manual?
Questions and answers