Subscribe to Our Youtube Channel
Related Manuals for Pentair WATERTRUST PRO Series
Summary of Contents for Pentair WATERTRUST PRO Series
- Page 1 WATERTRUST PRO SERIES™ WHOLE HOUSE IRON REDUCTION SYSTEMS 1.0, 1.5 INSTALLATION AND OWNERS MANUAL ©2024 Pentair Residential Filtration, LLC pentair.com...
-
Page 2: Table Of Contents
Programming the Lockout Feature .............. 11 Level III Cycle Programming- C Values ............11 Exploded Views and Parts Lists ............... 12-16 Troubleshooting ..................17-19 Maintenance Schedule ................20 Warranty Information .................. 24 2 • WaterTrust Pro Series Whole House Iron Reduction Service Manual... -
Page 3: Application Limitations
• This system must be installed in accordance with all applicable state and local laws and regulations. • This system is designed to treat cold water only and can be installed on any cold water supply. WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 3... -
Page 4: Pre-Installation Instructions
• To drain the plumbing system, open all the faucets in the house and flush the toilets. This procedure will allow air to enter the plumbing system. The water will drain out of the lowest faucet or outlet. 7. Bypass the Outside Faucets 4 • WaterTrust Pro Series Whole House Iron Reduction Service Manual... - Page 5 Since no regeneration chemicals are added, the discharge water may be drained to the outside and used for irrigation in climates where freezing is not a concern. Please note that iron in the drain water may cause staining, so avoid situations where the water may WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 5...
-
Page 6: Valve Layout
Valve Layout Two Piece Valve Disc Spring Optical Sensor Valve Discs Camshaft Control Motor Outlet Drain Injector Screen Filter Injector and Cap Inlet Backwash Drain Control Air Draw Valve Connection 6 • WaterTrust Pro Series Whole House Iron Reduction Service Manual... -
Page 7: Control Layout
Lock settings are changed in Level II programming. REGEN: Used to command the control to regenerate and enable or 14. Indicates double regeneration. disable lockout setting. WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 7... -
Page 8: Programming Overview
(- - : - -) immediately upon power up. The Time of Day and Day of Week must be reset. All other programmed parameters are stored in the static memory and are retained during power outages. 8 • WaterTrust Pro Series Whole House Iron Reduction Service Manual... -
Page 9: Filter Quick Programming
If a delayed regeneration is not desired, press the REGEN button to disable the delayed regeneration and the system will regenerate by water usage. WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 9... -
Page 10: Level Ii Programming
Number of regenerations Pd = Remote switch operation (742 only) 0 - 65,536 since last serviced See the Logix Professional dealers manual for further details on setting Level II parameters. 10 • WaterTrust Pro Series Whole House Iron Reduction Service Manual... -
Page 11: Programming The Lockout Feature
Rinse residuals and compact the media 2nd Backwash 0-200 1 Min Set to zero 2nd Fast Rinse 0-200 1 Min Set to zero Regenerant Refill Not Adjustable 1 Min Set to zero WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 11... -
Page 12: Exploded Views And Parts Lists
BYPASS PARTS SHOWN IN THE ABOVE DRAWING ARE NOT SOLD STAND-ALONE ITEM NO. PART NUMBER DESCRIPTION QTY. 1034386 BODY ASSY,BY-PASS,1265 1034300 ROTOR BYPASS ASSY 1034298 CLIP,RETAINER,BY-PASS 1030541 GASKET,PIPE ADAPTER 12 • WaterTrust Pro Series Whole House Iron Reduction Service Manual... - Page 13 Control Exploded View 10A* Speci c AIO parts WARNING: Do not use the flow control ball with #10A. WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 13...
- Page 14 Motor Lock Pin 44149 Autotrol 268 Valve Transformer US 1242168 762 Controller NA 1242162 742 Controller NA * not shown in the drawing * not shown in the drawing 14 • WaterTrust Pro Series Whole House Iron Reduction Service Manual...
- Page 15 1” Male Npt Fitting Connectors 38933 Distributor Assembly, 1.0 38932 Distributor Assembly, 1.5 39516 10” x 44” Tank Sleeve, 1.0 not shown 39517 10” x 54” Tank Sleeve, 1.5 WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 15...
- Page 16 10.2 in. 57.4 in. 61.6 in. 10” x 54” 10.2 in. 57.4 in. 61.6 in. 5 in. 11.8 in. 19.5 in. 4.2 in. DIM A DIM C DIM B 16 • WaterTrust Pro Series Whole House Iron Reduction Service Manual...
-
Page 17: Troubleshooting
3. Verify that the riser tube is seated correctly upper distributor. and is not cracked. If the troubleshooting guide did not resolve the unit’s symptoms, please contact your local Dealer for service. WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 17... - Page 18 12” water column above the check valve) 4. Replace the O-ring. (code 1010428) If the troubleshooting guide did not resolve the unit’s symptoms, please contact your local Dealer for service. 18 • WaterTrust Pro Series Whole House Iron Reduction Service Manual...
- Page 19 —Wire harness, Motor and Optical Sensor Assembly —Controller Four dashes displayed: Power failure occurred. Press SET to reset the time display. — — : — — WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 19...
-
Page 20: Maintenance Schedule
* Electronical parts – durability strongly affected by power source quality and stability ** Elastomer durability is strongly affected by raw water concentration in chlorine and its derivate *** Wear part. 20 • WaterTrust Pro Series Whole House Iron Reduction Service Manual... - Page 21 Notes WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 21...
- Page 22 22 • WaterTrust Pro Series Whole House Iron Reduction Service Manual...
- Page 23 WaterTrust Pro Series Whole House Iron Reduction Installation and Owners Manual • 23...
-
Page 24: Warranty Information
P: 262.238.4400 | Customer Service: 800.279.9404 | tech-support@pentair.com | pentair.com All indicated Pentair trademarks and logos are property of Pentair. Third party registered and unregistered trademarks and logos are the property of their respective owners. ©2024 Pentair. All Rights Reserved.
Need help?
Do you have a question about the WATERTRUST PRO Series and is the answer not in the manual?
Questions and answers