Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gimenez Ganga Saxun Aneas 80x40 motorised
Summary of Contents for Gimenez Ganga Saxun Aneas 80x40 motorised
- Page 1 Technical Manual Aneas 80x40 motorised...
-
Page 3: Table Of Contents
Index 1. Technical characteristics ............................4 1.1 Motorisation accessory kit ................................6 2. Main technical data ..............................7 2.1 Measurements and key data .................................8 3. Guide preparation ..............................10 3.1 Mounting the drive support ................................10 3.2 Fitting the belt and assembling the drive support ......................10 3.3 Assembly of the drive pulley .............................. -
Page 4: Technical Characteristics
1. Technical charactteristics Wall to wall Aneas 80x40 Patio cover with crossbar Aneas 80x40 Patio cover without crossbar Aneas 80x40 Mobilisation Installation possibilities Motorized Automated Manual Terrace Wrought Profiles Supports Guide profile Floor Ø10 Ø10 Ø10 Wall Structural profile 80,50 14,80 33,20 Ø10... - Page 5 TECHNICAL MANUAL ANEAS 80X40 MOTORISED Exploded view of motor components Components Nº Description Nº Description Transmission tube 80x40 guide Drive support Belt Bushing without square insert Drag pulley Bearing Return support Drive pulley Return pulley 13 mm axle brake Motor 13 mm square axle Motor support...
-
Page 6: Motorisation Accessory Kit
1.1 Motorisation accessory kit Drive support Return support Transmission tube Guide profile Drag pulley Toothed belt... -
Page 7: Main Technical Data
TECHNICAL MANUAL ANEAS 80X40 MOTORISED 2. Main technical data Maximum and minimum distance between sticks Maximum 60 cm Minimum 50 cm Maximum assembly dimensions Assembly with 2 guides 5 metres of line by 5 metres of output 5 metres of line by 9 metres of output In this case the guides will have to be spliced, with an inter- mediate structural support as a brace. -
Page 8: Measurements And Key Data
Important The installer is responsible for fixing the supports correctly, taking advice when necessary from professionals in the sector on the appro- priate fixing elements based on the surface where the product will be fixed. They are responsible for this operation and for guaranteeing its correct assembly and subsequent functioning. - Page 9 TECHNICAL MANUAL ANEAS 80X40 MOTORISED Output Output total (OT) Guide profile = OT-19,6cm Line *Guides inwards. Line total (LT) Transmission tube = LT-2V-15,5cm Overhang (O) Overhang (O) Maximum overhang = 100 cm *End guides (with motor box). Line total (LT) (*) (*) From outside to outside of support wings Toothed belt Toothed belt = (GUIDE PROFILE LENGTH X 2) +29 cm...
-
Page 10: Guide Preparation
3. Guide preparation 3.1 Mounting the drive support The ring gear shall be inserted into the support between the bearings, and the square axle shall be inserted from the side through the bearings and the ring gear. 3.2 Fitting the belt and assembling the drive support Place the guide with the pulley opening facing upwards and insert the belt through the hole shown in the picture towards the other end. - Page 11 TECHNICAL MANUAL ANEAS 80X40 MOTORISED Position the drive support in front of the guide and pass the belt around the drive ring gear, then insert it through the upper hole of the guide as shown in the following image, until the two ends of the belt are in the part of the guide where the return support will be housed. Assemble the drive support with the guide by positioning it inside the guide 4 mm from the inner stop, and once it is in place, drill it by placing the drill in the centre of the slotted hole (this will allow us to have a margin of adjustment when they are hung for assembly on site).
-
Page 12: Assembly Of The Drive Pulley
3.3 Assembling the drag pulley At the other end of the guide, close the belt with the drag pulley. To do this, loosen the four screws on the top plate of the belt, in- sert three teeth of each end of the belt between the connecting plates and fix it again with the four previously loosened screws (note the mounting position of the pulley shown in the picture). - Page 13 TECHNICAL MANUAL ANEAS 80X40 MOTORISED Once the return pulley has been positioned on the belt, insert the drag pulley into the guide and mount the return support by bringing the guide up to its inner stop. Nylon separator Threaded axle Nylon separator DIN 1587 M8 To fix it, drill the guide through the holes in the support and screw it in place.
-
Page 14: Installation
4. Installation 4.1 Hanging the guides Fix the guides to the structure profile or the wall using the slotted holes of the supports. The supports must be perfectly aligned and securely anchored, respecting the following dimensions between the centres of the supports according to each case: 2 guides: d=LT-2O-40 LINE TOTAL... -
Page 15: Mounting The Transmission Tube
TECHNICAL MANUAL ANEAS 80X40 MOTORISED 4.2 Mounting the transmission tube First, the brakes shall be positioned on the square axles. They shall not be tightened until the transmision tube is mounted and the axles are in their final position. The transmission tube shall then be mounted by first inserting one end of the tube into the square axle of one of the guides. Next, move the axle of the other guide so that it can be inserted into the other end of the transmission tube. -
Page 16: Mounting The Fabric
Finally, the motor is mounted by inserting the free end of the square axle through the motor transmission tube bushing and attaching the other end to the structure or wall using the support bracket. Support bracket Transmission tube with motor 4.3 Mounting the fabric Once the guides and the motor have been mounted and the drive system has been tested to ensure correct operation, by opening and closing it, the fabric can be mounted onto the awning. - Page 17 TECHNICAL MANUAL ANEAS 80X40 MOTORISED Then, after disassembling the belt redirection screw and roller from the driving support, insert the mobile pulleys into the guides through the lower holes of these supports. Take care to ensure that the drag pulleys are sufficiently separated from the supports to allow space for all the mobile pulleys to be positioned behind them.
- Page 18 Next, connect the first stick to the drag pulleys by means of the strips previously inserted in it. Finally, fix the belt in place by tightening the DIN 912 M8X60 screws of the return support. The tightening of both screws shall be done alternately to avoid jamming the belt and seizing the screws.
- Page 19 Giménez Ganga, S.L.U. Polígono Industrial El Castillo C/ Roma, 4 • 03630 Sax (Alicante) • España saxun.com...
Need help?
Do you have a question about the Saxun Aneas 80x40 motorised and is the answer not in the manual?
Questions and answers