Toro 04619 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. 04619
  6. Operator's manual
Toro 04619 Operator's Manual

Toro 04619 Operator's Manual

8, 11 and 14 blade dpa reel mower
Hide thumbs Also See for 04619:
Table of Contents

Advertisement

Quick Links

Download this manual
Form No. 3369-628 Rev A
8, 11 and 14 Blade DPA Reel
Mower
Greensmaster
®
3000 Series Traction Unit
Model No. 04618—Serial No. 312000001 and Up
Model No. 04619—Serial No. 312000001 and Up
Model No. 04624—Serial No. 312000001 and Up
To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Original Instructions (EN)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 04619 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Toro 04619

Summary of Contents for Toro 04619

  • Page 1 Model No. 04618—Serial No. 312000001 and Up Model No. 04619—Serial No. 312000001 and Up Model No. 04624—Serial No. 312000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)

  • Page 2: Table Of Contents

    Whenever you need service, genuine Toro parts, or Contents additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 Introduction..............2 identifies the location of the model and serial numbers Safety ................

  • Page 3: Safety

    Toro replacement parts and • Always wear substantial shoes. Do not operate accessories to keep the Toro all TORO. Never use cutting units while wearing sandals, tennis shoes, "will-fit" replacement parts and accessories sneakers or shorts.

  • Page 4: Setup

    Setup Media and Additional Parts Description Qty. Ball stud Mount to roller Operator’s Manual Read before installing and operating cutting unit Parts catalog Use to reference part numbers Certification of compliance CE Certification Installing the Front Roller No Parts Required Procedure The cutting unit is shipped without a front roller.

  • Page 5: Propping Up The Cutting Unit

    Propping up the Cutting Unit No Parts Required Procedure Whenever the cutting unit has to be tipped to expose the bedknife/reel, prop up the rear of the cutting unit to make sure the nuts on the back end of the bedbar adjusting screws are not resting on the work surface (Figure 6).

  • Page 6: Repositioning The Counter Weights

    Repositioning the Counter Weights No Parts Required Procedure Figure 8 The cutting units are shipped with the counter weight 1. Drive spline 3. Allen head screw (2) mounted to the right end and the motor mount to the 2. Motor mount left end of the cutting unit.

  • Page 7: Adjusting The Rear Roller

    Should excessive reel drag be evident, it will be either necessary to backlap or regrind the cutting unit to achieve the sharp edges needed for precision cutting (see the Toro Reel Sharpening Manual). Figure 9 1.

  • Page 8: Adjusting The Height Of Cut

    Figure 12 1. Spacer 3. Sideplate mounting flange 2. Roller bracket Figure 13 2. To adjust rear roller proceed as follows: 1. Sideplate mounting capscrews A. Raise the rear of the cutting unit and place a block under the bedknife. Important: Whenever the cutting unit has to be B.

  • Page 9: Adjusting The Cut-Off Bar

    Figure 16 1. Gauge bar 4. Rotate the adjusting screw until the front roller Figure 14 contacts the gauge bar. Adjust both ends of the roller until the entire roller is parallel to the bedknife. 1. Height-of-cut arm 3. Adjusting screw 2.
  • Page 10 Adjusting the Cut-Off Bar No Parts Required Procedure Adjust the cut-off bar to assure the clippings are cleanly discharged from the reel area: 1. Loosen the screws securing the top bar (Figure 17) to the cutting unit. g014643 Figure 17 1.

  • Page 11: Product Overview

    A selection of Toro approved attachments and accessories are available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories.

  • Page 12: Operation

    Operation bedknife. If a file is occasionally run across the front edge to remove this burr, improved cutting can be obtained. Note: Determine the left and right sides of the After extended running, a ridge will eventually machine from the normal operating position. develop at both ends of the bedknife.

  • Page 13: Maintenance

    Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Servicing the Bedbar Removing the Bedbar 1. Turn bedbar adjuster screw, counterclockwise, to back bedknife away from reel (Figure 18). Figure 20 1. Bedbar bolt 3.

  • Page 14: Backlapping The Reel

    Note: Additional instructions and procedures on Backlapping are available in the Toro Sharpening Reel and Rotary Mowers Manual, Form No. 80-300PT. Note: For a better cutting edge, run a file across the front face of the bedknife when the lapping operation is completed.
  • Page 15 Notes:...
  • Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.

This manual is also suitable for:

04618Greensmaster 3000 series04624

Table of Contents