Toro 04618 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. 04618
  6. Operator's manual
Toro 04618 Operator's Manual

Toro 04618 Operator's Manual

8, 11, and 14-blade dpa reel mower traction unit
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Register at www.Toro.com.
Original Instructions (EN)
8, 11, and 14-Blade DPA Reel
Mower
Greensmaster
Model No. 04618—Serial No. 313000001 and Up
Model No. 04619—Serial No. 313000001 and Up
Model No. 04624—Serial No. 313000001 and Up
Form No. 3376-588 Rev B
®
3000 Series Traction Unit
*3376-588* B

Advertisement

Table of Contents
loading

Related Manuals for Toro 04618

Summary of Contents for Toro 04618

  • Page 1 8, 11, and 14-Blade DPA Reel Mower Greensmaster ® 3000 Series Traction Unit Model No. 04618—Serial No. 313000001 and Up Model No. 04619—Serial No. 313000001 and Up Model No. 04624—Serial No. 313000001 and Up *3376-588* B Register at www.Toro.com. Original Instructions (EN)

  • Page 2: Table Of Contents

    You are responsible for operating the product properly and safely. Contents You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product. Introduction ..............2 Safety ................3 Whenever you need service, genuine Toro parts, or additional Safety and Instructional Decals.

  • Page 3: Safety

    Look for units while wearing sandals, tennis shoes, sneakers, or the Toro logo to ensure genuineness. Using unapproved shorts. Also, do not wear loose fitting clothing which replacement parts and accessories could void the warranty could get caught in moving parts.

  • Page 4: Setup

    Setup Media and Additional Parts Description Qty. Ball stud Mount to roller Operator's Manual Read before installing and operating cutting unit Parts catalog Use to reference part numbers Installing the Front Roller The cutting unit is shipped without a front roller. Install the roller using the loose parts supplied with the cutting unit and installation instructions included with the roller.

  • Page 5: Propping Up The Cutting Unit

    Figure 7 1. Bedknife adjusting screw nut (2) Repositioning the Counter Weights The cutting units are shipped with the counter weight G020065 Figure 5 mounted to the left end and the motor mount to the right end of the cutting unit. To change the cutting unit to different 1.

  • Page 6: Adjusting The Bedknife To The Reel

    (Refer to the 3. Rotate the reel so that a blade crosses the bedknife edge Toro Manual for Sharpening Reel and Rotary Mowers, between the first and second bedknife screw heads on Form No. 09168SL).

  • Page 7: Adjusting The Height Of Cut

    Adjusting the Height of Cut Position the spacer above the sideplate mounting flange (factory setting) when height of cut settings range from Note: For heights of cut greater than 1.270 cm (0.500 inch), 1.6 to 6 mm (1/16 to 1/4 inch) (Figure 12). you must install the high height of cut kit.

  • Page 8: Adjusting The Cut-Off Bar

    Adjusting the Cut-Off Bar Adjust the cut-off bar to ensure that the clippings are cleanly discharged from the reel area: 1. Loosen the screws securing the top bar (Figure 17) to the cutting unit. Figure 16 1. Gauge bar 4. Rotate the adjusting bolt on the height-of-cut arms g014643 until the front roller contacts the gauge bar.

  • Page 9: Product Overview

    A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories.

  • Page 10: Operation

    Operation bedknife, or regrind the cutting unit to achieve the sharp edges needed for precision cutting (Refer to the Toro Manual for Sharpening Reel and Rotary Mowers, Note: Determine the left and right sides of the machine Form No. 09168SL).

  • Page 11: Maintenance

    Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Servicing the Bedbar Removing the Bedbar 1. Turn the bedbar adjuster screw counterclockwise, to back the bedknife away from the reel (Figure 19). g020056 Figure 21 1.

  • Page 12: Backlapping The Reel

    Note: Additional instructions and procedures on Backlapping are available in the Toro Sharpening Reel and Rotary Mowers Manual, Form Number 80-300PT. Note: For a better cutting edge, run a file across the front face of the bedknife and reel when the lapping operation is completed.
  • Page 13 Notes:...
  • Page 14 Notes:...
  • Page 15 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
  • Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.

This manual is also suitable for:

Greensmaster 3000 series0461904624

Table of Contents