Omron CJ2H-CPU64 Datasheet
  1. Manuals
  2. Brands
  3. Omron Manuals
  4. Computer Hardware
  5. CJ2H-CPU64 -
  6. Datasheet
Omron CJ2H-CPU64 Datasheet

Omron CJ2H-CPU64 Datasheet

Cpu units
Hide thumbs Also See for CJ2H-CPU64:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
SYSMAC CJ-series CJ2H CPU Units
CJ2H-CPU6@
Setting new standards in high-speed
machine control
• Small, Fast, Flexible:
Inheriting and improving CJ1 features, the CJ2 CPU Units
is the best choice for the machine control with high-speed
and high-capacity.
Features
• Even more program memory and data memory.
• Superior high-speed control performance: LOAD instructions execute in 16 ns, SINE instructions in 0.59 μs.
• Maximum throughputs with High-speed interrupt function
• Efficient debugging through highly improved Data tracing
• Secure system from memory error brought by Memory Self-restoration Function
• The more advanced motion control by the lower cost: Synchronous Unit Operation
• Increased I/O throughput speed by Immediate refreshing instructions with direct processing.
CSM_CJ2H-CPU_DS_E_3_1
CJ2H-CPU64
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CJ2H-CPU64 and is the answer not in the manual?

Questions and answers

Related Manuals for Omron CJ2H-CPU64

Summary of Contents for Omron CJ2H-CPU64

  • Page 1 Features • Even more program memory and data memory. • Superior high-speed control performance: LOAD instructions execute in 16 ns, SINE instructions in 0.59 μs. • Maximum throughputs with High-speed interrupt function • Efficient debugging through highly improved Data tracing •...

  • Page 2: Ordering Information

    International Standards • The standards are abbreviated as follows: U: UL, U1: UL (Class I Division 2 Products for Hazardous Locations), C: CSA, UC: cULus, UC1: cULus (Class I Division 2 Products for Hazardous Locations), CU: cUL, N: NK, L: Lloyd, and CE: EC Directives.

  • Page 3: General Specifications

    5 to 8.4 Hz with 3.5-mm amplitude, 8.4 to 150 Hz Vibration Resistance Acceleration of 9.8 m/s for 100 min in X, Y, and Z directions (10 sweeps of 10 min each = 100 min total) Conforms to JIS C60068-2-27.

  • Page 4: Performance Specifications

    DM Area * Bits in the EM Area can be addressed either by bit or by word. These bits cannot be addressed by CPU Bus Units, Special I/O Units, PTs, and Support Software that do not specifically support the CJ2 CPU Units.
  • Page 5 Interrupt tasks: 256 Number of Tasks (Interrupt tasks can be defined as cyclic tasks to create extra cyclic tasks. Therefore, the total number of cyclic tasks is actually 384 max.) • Local symbols: Can be used only within a single task in the PLC.

  • Page 6: Function Specifications

    The response time can be decreased to enable detecting shorter input pulses. Basic I/O All of the outputs on Basic I/O Units can be turned OFF when an error occurs in RUN or Units Load OFF Function MONITOR mode.
  • Page 7 Serial Gateway This gateway enables receiving and automatically converting FINS to the CompoWay/F. Tasks can be executed at a specified interval (minimum of 0.2 ms or 0.1 ms *, Unit: 0.1 ms). Scheduled Interrupts * When High-speed interrupt function is used.
  • Page 8 This function detects an error when the same unit number is set for two or more Units, the Unit/Rack Number same word is allocated to two or more Basic I/O Units, or the same rack number is set for two Duplication Error or more Racks.

  • Page 9: Unit Versions

    Note: User programs that use functions of CJ2H CPU Units with unit version 1.2 or later cannot be used with CJ2H CPU Units with unit version 1.1 or earlier. If an attempt is made to transfer a program that uses any of these functions from the CX-Programmer to a CPU Unit with unit version 1.1 or earlier , an error will be displayed and it will not be possible to download to the CPU Unit.
  • Page 10 *4. A Programming Console cannot be used with a CJ2H CPU Unit. Device Type Setting The unit version does not affect the setting made for the device type on the CX-Programmer. Select the device type as shown in the following table regardless of the unit version of the CPU Unit.

  • Page 11: External Interface

    − Connector hood Protection earth Note: Do not use the 5-V power from pin 6 of the RS-232C port on the CPU Unit for anything but the NT-AL001-E Link Adapter. The external device or the CPU Unit may be damaged.
  • Page 12 CJ2H-CPU6@ Dimensions (Unit: mm) CJ2H CPU Unit CJ2H-CPU6@ 66.2 48.8 74.5...

  • Page 13: Related Manuals

    Also refer to the Hardware User’s Manual (W472) CJ2H-CPU6@-EIP CJ2H-CPU6@ CS1G/H-CPU@@H CS1G/H-CPU@@-V1 CS/CJ/NSJ-series Describes each programming instruction in detail. W474 CJ1G/H-CPU@@H Instructions Reference Information on instructions Also refer to the Software User’s Manual (W473) when you CJ1G-CPU@@ Manual do programming. CJ1M-CPU@@ NSJ@-@@@@(B)-G5D NSJ@-@@@@(B)-M3D CJ2H-CPU6@-EIP CJ2H-CPU6@ CS1G/H-CPU@@H CS1G/H-CPU@@-V1...
  • Page 14 PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability.

This manual is also suitable for:

Cj2h-cpu65Cj2h-cpu66Cj2h-cpu67Cj2h-cpu68Sysmac cj-series

Table of Contents