Subscribe to Our Youtube Channel
Related Manuals for SanRex SKY 4 HD T
Summary of Contents for SanRex SKY 4 HD T
- Page 1 INSTRUCTION MANUAL FOR WELDING WIRE FEEDER SKY 4 HD T Info : www.sanrexwelding.com - tel. (516)625-1313...
-
Page 2: Declaration Of Conformity
The RoHS Directive 2011/65/EU Type of equipment WIRE FEEDER Type of designation WF1300T - SKY 4 HD T Brand name or trade mark Manufacturer or his authorized representatives established within the EEA: Name, address, phone, website: SanRex Corporation, 50 Seaview Boulevard Port Washington NEW YORK 11050-4618 USA P. - Page 3 INDEX 4- SAFETY 6- INSTALLATION 7- CONTROLS 8- HUB ASSEMBLY MOUNTING 9- PROBLEM SOLUTIONS 10- ELECTRIC DIAGRAM 13- SPARE PARTS 14- FEED PLATE SYSTEM 16- SERIAL NUMBER...
- Page 4 must be free from damage to the insulation. BARE SAFETY CABLES ARE DANGEROUS. Do not use the ELECTRIC SHOCK CAN KILL machine if the power cable is damaged; it must be - Disconnect the power supply before working on replaced immediately. the welding machine.
-
Page 5: Disposal Of Electrical And Electronic Equipment
protective glass according to standards (degree of DISPOSAL OF ELECTRICAL AND protection DIN 10). ELECTRONIC EQUIPMENT - warn people in the vicinity not to look directly at the arc. dispose electrical equipment together with normal PREVENTION OF FIRE waste! In observance of European Welding produces splashes of molten metal. - Page 6 ATTENTION We kindly thank You for the confidence : NWORLD reserves the rigth to alter characteristics at any time without notice. You showed in purchasing one of our NWORLD assumes no liability for results of a wrong products. application of the products which may cause damage to We are sure You will not disappoint Your persons or equipment.
- Page 7 CONTROLS 1- Digital voltmeter and ammeter 4- Welding voltage adjustment 2- 2/4 stroke latching Allows welding voltage when the wire feeder is combined to electronic power sources. In alternative to - Unlatched (2 stroke): this function, we can put on wire feeder regulate a time A - press: continuous welding whilst switch is held of welding (spot-welding ).
- Page 8 HUB ASSEMBLY MOUNTING 1- Remove the hand (hub) nut from the hub assembly 6- Lower the pressure roll (3), refit it into the initial wire guide. position by the lever (2), adjusting the pressure with the knob. Minimum pressure is sufficient so 2- Place the wire reel on the hub so that the wire will as not to allow the feeding rolls to slip.
- Page 9 FAULT POSSIBLE CAUSE AND REMEDY 1. Weld deposit ‘Stringy’ and incomplete 1a. Torch moved over workpiece too quickly 1b. Gas mixture incorrect 2. Weld deposit too thick 2a. Torch moved over workpiece too slowly 2b. Welding voltage too low 3. Arc unstable, excessive spatter while 3a.
-
Page 11: Technical Dates
DIMENSIONS: Height (inc. of handle) 520mm 300mm Width 700mm Length (inc. of connectors) 20 kg WEIGHT ( approx. ) SanRex Made in Italy SKY 4 HD T S/N: Type EN 60974-1 IP IP 23 S NORM. EN 60974-10 24Vac 100% 50/60 Hz... - Page 13 ELENCO PARTI POS. NUMERO PARTE TITOLO QTÀ 19NW03-001 UNIVERSAL HANDLE SKY 19NW03-006A SKY EVOLUTION FRONT PANEL 19NW03-009 SKY EVP LEFT SIDE COVER 19NW03-B1 UNIVERSAL BASE SKY EVOLUTION 19NW03-S02 RIGHT SIDE COVER SKY EVOLUTION 22NW05-001 FRONT STICKER SKY 4 HD SAREX 428521 HINGE CMM.40-P-m5X12 ATC000021...
- Page 14 TYPE NW 01042...
- Page 15 TYPE NW 01042 pos. piece Description part. NO. Vite fiss.rulli screw VTE000001 Cuscinetto Ball bearing CTS002725 Distanziale piccolo Spacer narrow DPF000895 Distanziale grande Spacer large DGF020040 Perno portarullo Axle PPR100004 Portarullo sinistro Pressure arm left PRS100005 Portarullo destro Pressure arm right PRD100007 Vite fissaggio portarullo Screw...
- Page 16 Info : www.sanrexwelding.com - tel. (516)625-1313...
Need help?
Do you have a question about the SKY 4 HD T and is the answer not in the manual?
Questions and answers