Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Lindsay Broadband LBDG-24V
Summary of Contents for Lindsay Broadband LBDG-24V
- Page 1 LBDG-24V LBDG-24V Strand Mount DOCSIS 3.0 24V PoE Gateway Installation Guide...
- Page 2 LBDG-24V IMPORTANT SAFETY AND INSTALLATION WARNINGS WARNING: ATTEMPT TO SERVICE THIS PRODUCT YOURSELF AS OPENING OR REMOVING COVERS MAY EXPOSE YOU TO DANGEROUS VOLTAGES OR OTHER HAZARDS. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL. MOUNTING: Mount this product only as described in the installation instructions, otherwise it may fall causing serious personal injury and/or damage to the device.
-
Page 3: Replacement Parts
Unauthorized substitutions may result in fire, electric shock or other hazards. SERVICE DEPOT: Canada: Lindsay Broadband Inc., 2035 Fisher Dr., R.R. #5 Peterborough, Ontario K9J 6X6 (705) 742-1350... -
Page 4: General Description
LBDG-24V 1.1 Introduction This manual is written to help service perso nnel understand and install the Lindsay LBDG-24V DOCSIS 3.0 24V PoE Gateway. This first section gives a block diagram and a full product description. The remaining sections provide component... -
Page 5: Major Components
LBDG-24V 1.3 PoE Capability The Gateway can deliver up to 20W of PoE power. It is compatible with any device that accepts passive PoE (Passive PoE devices must accept power using pins 4 & 5 for +V and pins 7 & 8 for -V). Power is non-isolated. - Page 6 LBDG-24V 1.6 Interface Board The interface circuit board, which is located in the housing base, provides the interface to the HFC network. The following features are provided: An AC/RF filter is used to separate the AC power from the RF carriers.
- Page 7 LBDG-24V SECTION 2 COMPONENTS IDENTIFICACION SURGE WEATHER ARRESTOR SEAL HFC INPUT UPSTREAM & DOWNSTREAM PADS CABLE MODEM -20dB F CONNECTOR TEST POINT INTERFACE BOARD INTERRUPT SMPS INJECTOR GigE PoE PORT EMI SEAL...
-
Page 8: Section 3 Installation
LBDG-24V SECTION 3 INSTALLATION Installation of the LBDG-24V DOCSIS 3.0 Gateway is similar to the installation of a line extender or any other piece of CATV equipment. The DOCSIS Gateway can be connected to a power-passing coupler or splitter. Call Lindsay Broadband for the recommended power insertion device for your application. -
Page 9: Power Requirements
LBDG-24V 3.2 Power Requirements The DOCSIS 3.0 Gateway can be connected to any power-passing coupler or splitter. Use the following chart to estimate your AC current requirements based on line voltage and maximum PoE requirement: 3.3 Installation Diagrams Strand Mount... - Page 10 LBDG-24V 3.4 Installation 1. Pull the AC interrupt in the power-passing coupler or splitter. 2. Using the diagrams in this section as a guide, mount the Gateway at its final location. If using hanger brackets, the existing strand clamps should be lef t in place to act as spacers allowing the same bolts to be used.
-
Page 11: Ethernet Cable Installation
LBDG-24V 3.5 Ethernet Cable Installation The external RJ45 connector on the Lindsay LBDG-24V Gateway provides an IP68 weather-tight connection. A cable that is pre-terminated with an RJ45 connector can be used. No tools are required. 1. The parts kit (P/N 3501-288) for the connector contains two glands. The smaller gland is suitable for cables ranging in diameter from 4mm to ”... - Page 12 LBDG-24V SECTION 4 LBDG-24V HOUSING DIMENSIONS 4.1 Housing Dimensions...
- Page 13 LBDG-24V 4.2 Table of Specifications Lindsay LBDG-24V Gateway with DC Power Supply Specifications Cable Modem Band Plans DOCSIS (Annex B) Network Configuration and Management TFTP, SNMP (V1, V2c, V3), Telnet, HTTP 75 Ω Input Impedance Privacy BPI+ Downstream Modulation 64 or 256 QAM...
Need help?
Do you have a question about the LBDG-24V and is the answer not in the manual?
Questions and answers