1. Manuals
  2. Brands
  3. Sumake Manuals
  4. Industrial Equipment
  5. SFR50M
  6. Instruction manual

Sumake SFR50M Instruction Manual

Automatic screw feeder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
SFR50M
ITEM NO.:
AUTOMATIC SCREW FEEDER
SFR50M-I-2401D-K2
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SFR50M and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sumake SFR50M

Summary of Contents for Sumake SFR50M

  • Page 1 INSTRUCTION MANUAL SFR50M ITEM NO.: AUTOMATIC SCREW FEEDER SFR50M-I-2401D-K2...
  • Page 2 Safety Instructions PLEASE NOTE FOLLOWING CONDITIONS BEFORE USING SUMAKE SFR50M ◎ For a normal performance, please install this machine on a flat and stable working table, do not slant or pad, otherwise machine function might be affected. Turn off the power switch and unplug the AC adaptor when this machine is not ◎...

  • Page 3: Table Of Contents

    CONTENTS Check Before Operation ....................3 Accessories Included ....................4 Check The Screw Sise ....................4 Function With Adjusting Holes On Housing And PCB ..........5 Adjustment ........................6 Adjust The Rail Assembly ..................6 Dismantle The Rail Assembly .................6 Install The Rail Assembly ................11 Force-down plate adjustment ................

  • Page 4: Accessories Included

    Accessories Included Please check if there are complete accessories included with your SFR50M: HEX Wrench 2.0*107mmL Type*1 Power Controller AC 100~240V/DC12V*1 Orbit Back-End Chip Rule Orbit Front-End Chip Rule 20*10*0.2mm*2pcs&0.5mm*6pcs 20*10*0.2mm*2pcs&0.5mm*6pcs Instruction Manual*1 Check The Screw Sise Measure the size precisely on each part of applied screw with a caliper.

  • Page 5: Function With Adjusting Holes On Housing And Pcb

    Function With Adjusting Holes On Housing And PCB A. Lock Gate Plate B. Power S.W. C. Indication Light D. DC Power Hole E. Grounding Hole...

  • Page 6: Adjustment

    Adjustment After checking the screw size, it needs to adjust all related parts according to the screw size for the first use. Adjust The Rail Assembly Dismantle The Rail Assembly Remove the fixing screws of guide assembly, dismantle the guide assembly. Remove the fixing screws (6pcs) of front housing and take off the front housing.
  • Page 7 3. Dismantle the fixing screws (4pcs) of feeding structure and take it off. 4. Facing the machine, use Hex wrench to loose the screw clockwise to open the lock gate upward. Facing the machine, use Hex wrench to loose the screw clockwise to open the lock gate rightward.
  • Page 8 6. Remove the fixing screws of rail assembly. The fixing screws of rail assembly 7. Draw out the rail assembly from the machine. ※Note The Following When Making Above Adjustment※ a. Before dismantling the rail assembly, please confirm the lock gate status is open.
  • Page 9 2. Remove the fixing screw on the rear end of side of rail assembly, take off the tooling plate. 3. According to Table b, insert the suitable tooling plate into the rail groove for the width required and tighten the screw of step 1.2.
  • Page 10 ※ Combination Of The Thickness For Reference ※Table B Dia. of Screw Bolt Accessory-Tooling Dia. of Screw Accessory-Tooling (d) mm Plate (Rear) mm Bolt (d) mm Plate (Rear) mm 0.5*2+0.2*2=1.4 0.2 + 0.5 * 5 = 2.7 0.2*3+0.5 *2 = 1.6 0.2 + 0.5 * 6 = 3.2 0.2 * 2 + 0.5 * 3 = 1.9 0.2 + 0.5 * 7 = 3.7...

  • Page 11: Install The Rail Assembly

    Install The Rail Assembly Insert the adjusted rail assembly into the machine. Then fasten the fixing screws. Install the feeding structure, and then fasten screws.
  • Page 12 Adjust up and right gate to make distance between rail and gate around 0.2~0.5mm. 0.2~0.5mm Loosen rail fixing screw, adjust distance between the front of rail and disc around 0.2~0.5mm, fasten the screw. 0.2~0.5mm ※ NOTE a. Rail installation must keep 0.2~0.5mm gap with disc, must not be touched. b.

  • Page 13: Force-Down Plate Adjustment

    Force-down plate adjustment 1. Loosen fixing screw on force-down plate. 2. Use accessory tooling plate adjust height of force-down plate and then fasten screw in step1. 3. Put some screws into the groove and slide it up, to check whether the movement is smooth.

  • Page 14: Distribution Mechanism Adjustment

    Distribution Mechanism adjustment 1. Loosen fixing screw from front of distribution mechanism. 2. Align disc gap with central of rail by adjust front of distribution mechanism by left and right, fasten the loosen screw in step 1. 3. Loosen two hexagon screws.
  • Page 15 4. Adjust from part by up and down to make disc and rail flush, and then fasten loosen screw in step 3. Flush ※ NOTE ※ a. Align disc gap with central of rail, and upper plane cannot higher than upper plane of front rail.

  • Page 16: Adjust Sensor Function

    Adjust Sensor Function 1. Loosen the fixing screw of sensor fixing plate. 2. Make sure to cover half of the hole, and then fasten the screw of step 1. ※ NOTICE ※ Make sure to cove half of the hole and do adjustment to ensure the sensor function no problem.

  • Page 17: Adjust V Chase On Scooping Chamber Back

    Adjust V Chase on Scooping Chamber Back The V Chase is located on top of the rail and fastened to the back of Roller Assembly. The purpose is to catch fallen screws from the Rollers, and guide screws back to the rail. 1.

  • Page 18: Adjust The Brush

    Adjust the Brush 1. Swing the brush to stay almost horizontal, loosen screw on the side of brush bracket. 2. Place 5~8 screws into the rail groove close to the holding plate rear end and loosen 2 screws on the side of the brush bracket. Swing the brush and adjust the height until the brush just touch the screw heads slightly and tighten the screws after adjustment.

  • Page 19: Method Of Operation

    Method of Operation Load Screws Into the Chamber Turn off the power first and open the Top Cover Box. Ensure the screws are loaded without foreign materials, pour in screws until they come up to 1~2mm below the top on both sides of the rails.

  • Page 20: Pick Up Screws

    Pick Up Screws Make sure the bit type on your electric screwdriver matches the head of the screw, and the bit is magnetized before use.(Bit that not magnetized will not stick with the screw and screw will fall off after picking up). Hold the screwdriver and put the driver bit above the Bit Guide and push it straight down to "+"...

  • Page 21: Counter Interface Operation

    Counter interface operation Display interface diagram Setting： 1. Press the SET button for 3 seconds to enter system setting. Select setting options when the SET light is on. Now the first two digits led are flashing for changing and press the UP or DN button to select item number that you wish to change its value.
  • Page 22 Feature Comparison Table Item Feature Definition (UP/ DN) Target Quantity Count Quantity Setting (Value: 00~99 screws (00 means Off this function)) Count Quantity Increment or Item 01 Count Method Decrement Setting (Value: 00 Increment; 01 Decrement) Buzzer is on or off. Buzzer Setting (Value: 00 ON;...
  • Page 23 adjustment. 2. Since gape selection is depending on the thickness of screw’s head, please choose value 01 for the thickness less or equal to 0.5mm and value 00 for other that greater than 0.5mm. Fault codes and meanings Code Error Summary E-01 Alert: Roller Motor Jam Notification E-02...

  • Page 24: Troubleshooting

    Troubleshooting Please power off for examination once needed. Status Caused Solution No AC power or loose cable Check the power controller Screws quantity too much Take some screws out No action after power on Switch, motor, PCB malfunction Replace Switch, motor or PCB or come with abnormal Clean it up Screws fall in to the inside of machine...

  • Page 25: Maintenance & Cleaning

    Maintenance & Cleaning Turn off the POWER before performing maintenance and cleaning. CLEANING AND MAINTENANCE THE BRUSH Using the dry cotton to wipe the brush to remove the dust, Swing the brush by hand and adjust the height of the brush to make the brush in touch with screw heads. Replace the brush when brush hair is too worn and cannot wipe down screws in an improper position.

  • Page 26: International Warranty Conditions

    International Warranty Conditions The warranty is valid for 12 months from purchase date (based on 8 working hours a day). Please contact your supplier during the warranty period for repair or maintenance. ❖ NOTE: 1. The service cost shall be considered as chargeable if the failure/cost was induced by any of the following conditions: -Failure due to improper handling or un-authorized modification.
  • Page 27 EU Declaration of Conformity (DOC) SUMAKE INDUSTRIAL CO., LTD. 4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan declare in sole responsibility that the equipment Equipment： AUTOMATIC SCREW FEEDER Model/ Serial No.： SFR50M The object of the declaration described above is in conformity with the relevant union harmonization legislation: ...
  • Page 28 NOTE www.SUMAKE.com www.aircompressors.com.tw...

Table of Contents