Table of Contents
Advertisement
Quick Links
ST-66107
INDUSTRIAL AIR TURBOLAP LINER TOOL
Parts List
No.
Parts No.
1
66107-01
2
66107-02
3
66107-03
4
66107-04
5
66107-05
6
66107-06
7
66107-07
8
66107-08
9
66107-09
10
66107-10
11
66107-11
12
66107-12
13
66107-13
14
66107-14
15
66107-15
16
66107-16
Description
Clamp
Spindle
Ball Bearing
Oil Seal
Front Case
Drive Shaft
Gear
Insert
Bearing
Oil Seal
Gear Axle
Upper cover OF Drive Shaft
Screw
Bearing
Oil Seal
Upper Housing
Q'ty
No.
Parts No.
1
17
66107-17
1
18
66107-18
1
19
66107-19
2
20
66107-20
1
21
66107-21
1
22
66107-22
1
23
66107-23
1
24
66107-24
2
25
66107-25
2
26
66107-26
1
27
66107-27
2
28
66107-28
4
2
29
66107-29
2
1
Description
Lower Housing
Housing Loop
Air Inlet
Oil Seal
Rear Air Shaft
Oil Seal
Oil Seal
Rear Base
Air Shaft Seat
Switch
Switch Fixture
Housing Cover
Spinlde Ass y [Incl. 2, 6, 7, 8,
Spinlde Ass'y [Incl 2 6 7 8
9(2), 10(2), 11, 12(2), 13(4),
14(2), 15(2)]
ST-66107-P-1810A-KS
Q'ty
1
1
1
1
1
1
1
1
1
1
1
1
1
Advertisement
Table of Contents
Related Manuals for Sumake ST-66107
Summary of Contents for Sumake ST-66107
- Page 1 ST-66107 INDUSTRIAL AIR TURBOLAP LINER TOOL Parts List Parts No. Description Q'ty Parts No. Description Q'ty 66107-01 Clamp 66107-17 Lower Housing 66107-02 Spindle 66107-18 Housing Loop 66107-03 Ball Bearing 66107-19 Air Inlet 66107-04 Oil Seal 66107-20 Oil Seal 66107-05 Front Case...
- Page 2 The TOOL HOLDER will take 5 mm diameter shank files and small diamond files or regular small files in 3mm Shank diameter. The patented “UNIVERSAL SWIVEL AIR INLET JOINT” with speed regulator is equipped for better maneuverability and speed control of the tool. ST-66107-I-1810A-KS...
- Page 3 CUTTER(SAW) Original instructions SUMAKE Industrial Co. Ltd.
- Page 4 The tool has been manufactured in conformity with the instruction of EU machine directive. The EU mark will be considered void in the event of inexpert repairs, the use of non-original parts and in case of non-observance of the safety instructions in the user’s manual. Possible direct or indirect consequential damages are not the responsibility of SUMAKE Industrial co., Ltd. General safety rules: Watch the tool at all times when in use.
- Page 5 other parts of the body. 2. While using the tool, the operator should adopt a comfortable posture whilst maintaining secure footing and avoiding awkward or off-balanced postures. The operator should change posture during extended tasks which may help avoid discomfort and fatigue. 3.
- Page 6 the hazard, the risk of injury and the avoidance action to take. General preparation and connection: Before connecting the air hose, apply 4 to 5 drops of SAE#10-20 spindle oil at the air inlet. Also, every 3 to 4 hours of operation, oiling is necessary.
Need help?
Do you have a question about the ST-66107 and is the answer not in the manual?
Questions and answers