Table of Contents
Advertisement
In case of difficulty
Operation to reset
For U.S.A. and Canada
;
Unplug the AC power cord from the wall outlet, then plug it
The microcomputer may fall into malfunction {impossibility to
back in while holding down the MEMORY key.
operate, erroneous
display, etc.) when the power cord is un-
plugged while power is ON or due to an external factor. {n this
Except for U.S.A. and Canada
case, execute the following procedure to reset the microcom-
puter and return it to normal condition.
KR-ASOGO [Er
Leave the AC power cord plugged in and switch the MAIN
POWER key OFF, then switch the MAIN POWER key ON while
holding down the MEMORY
key.
e Please note that resetting the microcomputer clears the contents
stored in it returns it to the condition when it left the factory.
ac
arate
en ammle
Ee
SSE sn ae feted HY $0 PL
eee oe
DAS RANARIES
SEALER
a l a t a aD
of unit
Remote cont
|
"Symptom
ee
es
Hemedy
Remote control operation is not possible.
|
Batteries are exhausted.
e Replace with new batteries.
-—3)
e The remote control unit is too far away fram | @ Operate the remote control unit within
the main system, controling angle is too
the controllable range.
.
large, or there is an obstacle in between.
e The audio cords and system control cords
are not connected properly.
@ The source component to be operated does
not contain the tape(s) or CD.
@ An attempt is made to play a tape which is
being recorded in the cassette deck.
—
e Connect
properly referring to "System
connections".
~
e Place the tape(s) or CD in the source com-
_
ponent to be played.
,
e Wait until the recording is completed.
Amplifier
Ch ener eeteh eotrelare ate
e Connect them properly referring to "Sys-
tem connections".
e Adjust the volume to a proper level.
Sound is not output.
The speaker cords are disconnected.
® The VOLUME
is set to the minimum pesi-
tion,
e The SPEAKERS switches are set
to OFF.
® Set the SPEAKERS switchtes} to ON.
# Turn the power off, eliminate the short-
circuiting, then turn on the power again.
~
|
The STANDBY
indicator blinks and sound
is not output.
# Speaker cords are short-circuited.
e Connect it properly referring to "System
connections".
e Adjust the Left/Right balance.
e The speaker cord is disconnected.
Sound
is not output
from
one
of the
speakers.
e The BALANCE control is set to an extreme
position:
e Insert the audio coed plugs securely into
the PHONO
jacks.
e Connect the grounding wire to the GND
termina! on the rear panel.
e@ The audio cord from the turntable is not in-
serted.securely into the PHONO jacks.
e The turntable is not grounded.
A hum
noise
is generated
when
the
PHONO input selector is selected.
Tuner
@ No antenna is connected.
e Connect an antenna.
e The broadcast band is not set properly.
@ Set the broadcast band properly.
e The frequency of the desired station is not
| # Tune the frequency of the desired station.
tuned.
-
interference.
e Noise due to ignition noise of an automobile.
| e Install the outdoor antenna away from the
road,
e Noise due to an influence from an electric {| @ Turn off the power to the appliance.
appliance.
e Noise due to a nearby TV set.
e Install the system farther away fram the
TV set.
the power cord had been unplugged for a
long period of time.
=
Do not use contact cleaners because it could cause a malfunction. Be specially careful against contact cleaners containing cil, for
Mie
they may deform the plastic components.
Advertisement
Table of Contents
