Table of Contents
Advertisement
GR/CH Button
Short press the GR/CH button can adjust the built-in wireless group. When the
group indicator on the LCD panel is blinking, turn the SET dial to change. And long
press the GR/CH button can adjust the built-in wireless channel. When the channel
indicator on the LCD panel is blinking, turn the SET dial to change.
Receiver Trigger Mode
Three receiver triggering modes are available and can be set by pressing <S1/S2>
receiver model button.
◆No optical control: S1 or S2 is not displayed on the LCD panel, indicating the
receiver triggering function is shut down.
◆Optical S1 Secondary Unit Setting: In M manual flash mode, press <S1/S2>re-
ceiver mode button so that this flash can function as an optic S1 secondary
flash with optic sensor. With this function, the flash will fire synchronously when
the main flash fires, the same effect as that by the use of radio triggers. This
helps create multiple lighting effects.
◆Optical S2 Secondary Unit Setting: Press <S1/S2>receiver mode button so that
this flash can also function as an optic S2 secondary flash with optic sensor in M
manual flash mode. This is useful when cameras have pre-flash function. With
this function, the flash will ignore a single "preflash" from the main flash and will
only fire in response to the second, actual flash from the main unit.
Buzz Function
The BUZZ button is used for deciding whether there is sound reminder for ready
flash after recharging. Short press the BUZZ button, when the buzz indicator is on
the LCD panel, the buzz function is working; when it is disappear, the buzz function
is not working. A "BI" sound will be heard when it' s fully charged.
Wireless Button
Press the <
> Button can turn on/off the built-in wireless transmission. If there
are no wireless and channel indicators displayed on the LCD panel, the built-in
wireless transmission is off. On the contrary, the built-in wireless transmission is
on. When turning the flash on, press the BUZZ button and C.Fn custom button
simultaneously, and factory setting can be restored.
C.Fn
Set it to OF or choose any figure from 01 to 99. When setting to
Wireless ID
F1
OF, wireless ID will be turned off. And 01 to 99 means the wireless
setting
ID is turned on.
Flash power
F2
It can be displayed in 1/P or P.P.
display
13
Alarm Display
The temperature sensor is not connected.
E0
E3
Discharged capacitance and voltage > rating +10%
Alarm sounds
BIBI, ringing per 0.5 second. Press SET button to stop alarming.
Memory Function
The device is equipped with memory function for the panel setting. It will help remem-
ber the panel setting 3 seconds after you set it. When starting up the flash next time,
the panel setting will be the same as that before powering it off.
Wireless Control Function
The flash unit has built-in 2.4G wireless transmission, which can be used together
with X1, X2, XPro and XT16 or FT-16 flash trigger.
Press the <
> Button and the <S1/S2> Button can turn on the built-in wireless trans-
mission and the <
> is displayed. If there are other wireless flash systems nearby,
you can change the channel IDs to prevent signal interference. The channel IDs of the
master unit and the receiver unit(s) must be set to the same.
Setting the Communication Channel
C H
C H
O F F
O F F
1
2
Long press the <GR/CH>
Turn the SET Dial to
Button for 2 seconds until
choose the channel
the channel IDs is blinking.
from 1 to 32.
Setting the Communication Group
C H
C H
O F F
O F F
1
2
Turn the SET Dial to
Short press the <GR/CH>
choose the group from
Button for 2 seconds until
0 to F.
the group IDs is blinking.
C H
O F F
3
Press the SET Dial to
confirm.
C H
O F F
3
Press the SET Dial
to confirm.
14
Advertisement
Table of Contents
