Advertisement
S2 Slave Trigger Mode
◆
When the "S2 Optic Slave Indicator (11)" lights up, the flash will ignore a single
"preflash" from the master flash and will only fire in response to the second, actual
flash from the master. In this mode, the flash can function as a slave flash. It is
applicable when using a TTL master flash. With this anti-preflash function,
synchronization is supported with cameras having a one-preflash firing system.
Buzz Function
The sound button (7) is used to decide whether there is sound reminder for ready
flash after recharging. When the buzz indicator (14) is on, it means buzz function is
working; if it is off, the buzz function is shut down. A "BI" sound will be heard when
it's fully charged.
Memory Function
The device is equipped with memory function for the panel setting. It will help
remember the panel setting 3 seconds after you set it. When starting up the flash
next time, the panel setting will be the same as that before powering it off.
Wireless Control Function
The flash unit is built in with a Wireless Control Port (18) so that you can
◆
wirelessly control the on-and-off of your flash, modeling lamp and buzzer, as well
as adjust the flash output level, etc.
To control the flash wirelessly, you need a Godox FT series remote control set
◆
(on-camera and on-flash), which is sold separately. Insert its receive end into the
Wireless Control Port (18) on the flash and insert the transmit end into the camera
hot shoe. Settings made on the hotshoe-mounted transmit and receive ends will be
wirelessly communicated to the flash. Then you can press the camera shutter-
release button to trigger the flash. You can also hold the transmit end at hand to
control your flash.
For full instructions on the use of FT series remote control, see its user manual.
◆
Tube Replacement
Shut down the power and remove the power cord before replacing the flash tube
and wear insulated gloves. Then, loosen the iron wire on the tube, keep a balanced
hold on the two feet of the flash tube and pull out the old tube gently. Take down the
feet casing from the old tube and put it on the new one. Hold two feet of the new
tube, and target directly towards the two copper outlets, then push them slightly in.
Twine the iron wire on the stainless steel sheet to fix the flash tube.
- 13 -
TECHNICAL DATA
Model
DP300
300Ws
Max Power (WS)
58
Guide Number(m ISO 100)
Color Temperature
AC110V-120V~60Hz or AC220V-240V~50Hz
Operating Voltage
Power Output Control
Modeling Lamp (W)
Triggering Method
Sync cord, Test button, Slave triggering, Wireless control port
Flash Duration
Parameters Output from
the Sync Cord Jack
Parameters Output from
5V/200mA (only for Godox receiver)
the USB Port
Fuse
AC220V-240V~50Hz: 5A
AC110V-120V~60Hz: 8A
Recycle Time
0.3-1.2s
Dimension
Flash diameter Φ12.5cm, height of flash with handle 21.5cm,
length of flash with modeling lamp 42cm
Approx
Net Weight
2.9kg
MAINTENANCE
Shut down the device immediately when it works abnormally and find out the reason.
Avoid sudden impacts and the lamp should be dedusted regularly.
It is normal for the lamp to be warm when in use. Avoid continuous flashes if unnecessary.
Maintenance of the flash must be performed by our authorized maintenance department
which can provide original accessories. The flash-tube and the modeling lamp are user-
replaceable. Replacement tubes and lamps can be obtained from the manufacturer.
This product, except consumables e.g. flash tube and modeling lamp, is supported with a
one-year warranty.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by professional.
Disconnect the power when cleaning the flash or when changing the flashtube / modeling
lamp.
Changes made to the specifications or designs may not be reflected in this manual.
DP400
DP600
DP800
DP1000
400Ws
600Ws
800Ws
1000Ws
65
80
88
92
5600±200K
OFF, 5.0~7.0(1/16~1/1)
150W
1/2000~1/800s
5V
8A
0.3-1.5s
0.4-2s
3.0kg
3.1kg
3.2kg
3.3kg
Made In China
- 14 -
Advertisement
