7.
MAINTENANCE
7.1.
REMOTE BATTERY REPLACEMENT
7.1.1. First open the battery cover on the back of the remote control and install a 3V CR2032 battery (not included).
7.1.2. To open the battery cover: first rotate counter-clockwise to detach the battery cover buckle, and then directly remove it.
7.1.3. When using, please aim at the receiver position.
7.1.4. When the battery power is used up, rotate the battery cover in the arrow direction and replace with new battery (CR2032 3V). Please
pay attention to the positive and negative terminals of the battery, and then restore the battery cover.
8.
CLEANING
DO NOT use chemical detergents when cleaning.
8
8.1.
Before any maintenance please unplug the power cord, otherwise it may cause electric shock.
If there is accumulation of dust on the surface, please wipe it with a soft or damp cloth.
8.2.
CLEANING OF THE HONEYCOMB COOLING PADS
8.2.1. Unplug the power cord, remove the screws on the rear and side windows and remove the pads.
8.2.2. Wash the cooling pad with gentle fresh running water, DO NOT use high pressure washer. DO NOT use acid or alkaline chemicals.
8.2.3. Ensure the honeycomb cooling pads are completely dry before replacing them back into the unit.
8.2.4. Use a soft cloth to remove any dust or debris from the rear and side windows before replacing.
8.2.5. Once dry put the honeycomb pads back into the unit, re-attach the rear and side windows fixing the screws in place.
8.2.6. CLEANING OF THE BODY SURFACE.
8.2.7. To clean the surface of the machine use a damp cloth DO NOT spray directly with water.
8.2.8. Do not use corrosive detergent or solvent for cleaning.
8.3.
TO EMPTY THE TANK
8.3.1. When the unit is not used for a long time, unplug the power, pack the unit and prevent dust from entering.
Before packaging, ensure that the cooling pad and dust-proof filter are totally dry, and there is no water left in the water tank.
8.3.2. To empty the tank pull out the water plug at the bottom of the tank to drain, ensure all water has been drained out before re-tightening
the water plug (fig.5).
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
BATTERY REMOVAL: SEE SECTION 6.5.3
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak's registered compliance scheme. Jack
Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
Refer to section 6.5.3 at end
of these instructions regarding
battery disposal.
sales@sealey.co.uk
Original Language Version
fig.5
fig.5
REGISTER YOUR
PURCHASE HERE
www.sealey.co.uk
SAC100 Issue 2 23/2/24