Table of Contents
Advertisement
Quick Links
1.
INSTRUCTIONS FOR USE ......................................................................... 30
2.
SAFETY PRECAUTIONS ............................................................................ 32
3.
ENVIRONMENTAL CARE ........................................................................... 34
4.
DESCRIPTION OF CONTROLS.................................................................. 35
5.
USING THE HOB......................................................................................... 36
6.
CLEANING AND MAINTENANCE ............................................................... 41
7.
POSITIONING IN THE COUNTER TOP...................................................... 44
8.
ELECTRICAL CONNECTION...................................................................... 47
9.
GAS CONNECTION .................................................................................... 48
10. ADAPTATION TO DIFFERENT TYPES OF GAS........................................ 50
THESE INSTRUCTIONS ARE VALID ONLY FOR THE DESTINATION COUNTRIES
WHOSE IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS
MANUAL.
IINSTRUCTIONS FOR THE USER: these instructions contain user
recommendations, a description of the controls and the correct
procedures for cleaning and maintenance of the appliance.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified
technician who must install the appliance, set it functioning and carry out
an inspection test.
@
Further information about the products can be found at www.smeg.com
Contents
29
Advertisement
Table of Contents
Related Manuals for Smeg PV630N
Summary of Contents for Smeg PV630N
-
Page 1: Table Of Contents
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must install the appliance, set it functioning and carry out an inspection test. Further information about the products can be found at www.smeg.com... -
Page 2: Instructions For Use
General instructions 1. INSTRUCTIONS FOR USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE HOB. -
Page 3: General Instructions
General instructions NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND SMOOTH ON THE COOKING HOB PAN STANDS. NEVER USE CONTAINERS WHICH PROJECT BEYOND THE OUTSIDE EDGE OF THE HOB. -
Page 4: Safety Precautions
DO NOT REMOVE THE PLATE ON THE CASING FOR ANY REASON. BEFORE CONNECTING THE APPLIANCE, ENSURE THAT IT IS SET TO THE TYPE OF GAS THAT IT WILL BE SUPPLIED WITH, CHECKING THE LABEL APPLIED UNDER THE CASING. BEFORE CARRYING OUT INSTALLATION/MAINTENANCE WORK, MAKE SURE THAT THE APPLIANCE IS NOT CONNECTED TO THE POWER GRID. - Page 5 General instructions DO NOT LET CHILDREN GO NEAR THE APPLIANCE WHEN IT IS IN OPERATION OR PLAY WITH IT AT ANY TIME. DO NOT INSERT POINTED METAL OBJECTS (CUTLERY OR UTENSILS) INTO THE SLITS IN THE APPLIANCE. DO NOT USE STEAM JETS FOR CLEANING THE APPLIANCE.
-
Page 6: Environmental Care
You can obtain the addresses of collection, recycling and disposal centres from your retailer or from the competent local organisations. Do not discard the packaging or any part of it, or leave it unattended. It can constitute a suffocation hazard for children, especially the plastic bags. -
Page 7: Description Of Controls
4-burner hob 5-burner hob KNOB DESCRIPTION To light the flame, press the knob and, at the same time, turn it anticlockwise to the minimum flame symbol To adjust the flame, turn the knob to the zone between the maximum ( ) and minimum ( ) settings. -
Page 8: Using The Hob
D on the hob. Positioning the pan stands The pan stands are provided unassembled on the hob. There are three types of pan stands the installer must be familiar with in order to position them correctly. Resting pan stand... -
Page 9: Instructions For The User
Instructions for the user To position each pan stand correctly on its burner, follow the instructions below: 4-burner hob 5-burner hob At the ends of the legs of the pan stands there are silicone rests with a hole that must be centred onto the... - Page 10 Then position the central pan stand (5-burner model) or the resting pan stand (4-burner model) so that the dent rests on the supporting bar of the support pan stand as shown in the figure.
- Page 11 When the burner is lit, the relevant activation knob will light up to indicate this. The knob will turn off a few seconds after it is turned to the O position or if the burner goes out accidentally. The knob light turns on and off gradually.
-
Page 12: Pan Diameters
Using the griddle plate A few precautions are necessary if you wish to use a griddle plate: • leave a gap of at least 160 mm between the edge of the griddle plate and the side wall; • if one of the burners close to the wooden rear wall is a triple crown burner, leave a gap of at least 160 mm between this wall and the edge of the griddle plate;... -
Page 13: Cleaning And Maintenance
To clean and preserve surfaces, always use only specific products that do not contain abrasives or chlorine-based acids. How to use: pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or a microfibre cloth. - Page 14 6.2.3 Stubborn encrustations If using the microfibre cloth is not enough, a brass wire sponge can be used together with stainless steel cream Crema inox or standard abrasive creams available in shops.
- Page 15 The burner pins A must be inserted in the housings B in the burner crown. The holes C in the burner crowns should be slid over the igniters and thermocouples D on the hob.
-
Page 16: Positioning In The Counter Top
Do not fix the hob using silicon as this would make it impossible to remove the hob, if necessary, without damaging it. - Page 17 Instructions for the installer If installed on top of an oven, the latter must be equipped with a cooling fan. In case of installation on an empty kitchen unit with doors, a separation panel must be placed under the hob. Keep a minimum distance of 10 mm between the bottom of the hob and the surface of the panel, which must be easily extractable to allow sufficient access for any technical assistance.
- Page 18 To secure the hob correctly to the counter top, tighten the brackets A in the appropriate holes on the sides of the casing. Take care while securing with the brackets; if tightened too much the glass may be strained causing it to crack.
-
Page 19: Electrical Connection
Do not remove this plate for any reason. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations. -
Page 20: Gas Connection
The cooker hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. For supplying it with other types of gas, see chapter "10. ADAPTATION TO DIFFERENT TYPES OF GAS". -
Page 21: Connection To Lpg
The air vents, protected by grills, must be the right size to comply with current regulations and positioned so that no part of them is obstructed, not even partially. -
Page 22: Adaptation To Different Types Of Gas
Before carrying out the following operations, disconnect the appliance from the power supply. The cooker hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. If other types of gas are to be used, the nozzles must be replaced and the primary air must be adjusted. - Page 23 Using a 7-mm wrench, remove nozzle E and replace it with the appropriate nozzle, following the instructions in the tables for the type of gas to be used. The nozzle tightening torque must be no more than 3 Nm.
-
Page 24: Adjustment For Natural Gas
Refers to distance “X” in mm. G30/G31 BURNER 30/37 mbar 20 mbar Auxiliary (1) Semi-rapid (2) Rapid (3) Ultra-rapid (4) To identify the burners on your hob, refer to the drawings in “10.6 Arrangement of the burners on the cooking hob”. -
Page 25: Final Operations
The bypass diameters for each individual burner are shown in table “10.2 Adjustment for LPG”. After adjustment with a gas other than the preset one, replace the label on the casing of the appliance with the label corresponding to the new gas. The label is... - Page 26 3. Rapid 4. Ultra-rapid 10.7 Lubrication of gas taps Over time the gas taps may become difficult to turn and get blocked. Clean them internally and replace the lubrication grease. This procedure must be carried out by a specialised technician.