Advertisement
1. INSTRUCTIONS FOR USE .............................................................. 22
2. SAFETY PRECAUTIONS ................................................................. 24
3. ENVIRONMENTAL RESPONSIBILITY ............................................. 26
4. USING THE HOB.............................................................................. 27
5. CLEANING AND MAINTENANCE.................................................... 29
6. POSITION NEAR THE COUNTER TOP ......................................... 30
7. ADAPTATION TO DIFFERENT TYPES OF GAS ............................ 36
8. FINAL OPERATIONS ....................................................................... 38
THESE INSTRUCTIONS ARE VALID ONLY FOR THE DESTINATION COUNTRIES
WHOSE IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS MAN-
UAL.
INSTRUCTIONS FOR THE USER: these instructions contain user
recommendations, a description of the controls and the correct
procedures for cleaning and maintenance of the appliance.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified
technician who must install the appliance, set it functioning and carry out
an inspection test.
Contents
21
Advertisement
Table of Contents
Related Manuals for Smeg PGF64
Summary of Contents for Smeg PGF64
-
Page 1: Table Of Contents
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must install the appliance, set it functioning and carry out an inspection test. -
Page 2: Instructions For Use
ANY OTHER USE. THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR USES OTHER THAN THOSE INDICATED. IF THE APPLIANCE IS INSTALLED ON BOATS OR IN CARAVANS, DO NOT USE IT AS A ROOM HEATER. NEVER USE THIS APPLIANCE TO HEAT YOUR ENVIRONMENT. -
Page 3: General Instructions
ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE (OFF) POSITION WHEN YOU FINISH USING THE APPLIANCE NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND SMOOTH ON THE COOKING HOB PAN STANDS. NEVER USE PANS OR GRIDDLE PLATES WHICH PROJECT BEYOND THE OUTSIDE... -
Page 4: Safety Precautions
DO NOT REMOVE THIS PLATE ON THE CASING FOR ANY REASON. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING. BEFORE CARRYING OUT INSTALLATION/MAINTENANCE WORK, MAKE SURE THAT THE APPLIANCE IS NOT CONNECTED TO THE POWER GRID. - Page 5 General instructions DO NOT LET CHILDREN GO NEAR THE APPLIANCE WHEN IT IS IN OPERATION OR PLAY WITH IT AT ANY TIME. DO NOT INSERT POINTED METAL OBJECTS (CUTLERY OR UTENSILS) INTO THE SLITS IN THE APPLIANCE. DO NOT USE STEAM JETS FOR CLEANING THE APPLIANCE.
-
Page 6: Environmental Responsibility
Therefore, at the end of the product's... -
Page 7: Using The Hob
If the burners should go out accidentally, after about 20 seconds a safety device will be tripped, cutting off the gas supply, even if the gas tap is open. Turn off the control knob and wait at least 1 minute before trying to re-light the burner. - Page 8 For better burner efficiency and to minimise gas consumption, use pans with a flat, smooth base and a lid that have a suitable size for the burner, thus preventing the flames reaching the sides of the pan (see paragraph “4.3 Pan Diameter”).
-
Page 9: Cleaning And Maintenance
To clean and preserve the stainless steel surfaces, use only specific products that do not contain abrasives or chlorine-based acids. How to use: pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or chamois leather. -
Page 10: Position Near The Counter Top
The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). - Page 11 Make sure that there is a minimum of 750 mm between the hob ring flames and any shelves placed directly above them (Fig. 1). Furthermore, this kind of appliance needs a milling on the hob top of 3 mm in depth; the measurements are indicated in figure 4 (detail A of figure 2).
- Page 12 IMPORTANT: if the appliance is mounted on a unit, make sure that a separating shelf is installed, as shown in the figure. However, if the appliance is on an oven installed under the hob, there is no need to install a separating shelf.
- Page 13 Do not remove this plate for any reason. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations.
- Page 14 The air vents, protected by grills, must be the right size to comply with current regulations and positioned so that no part of them is obstructed, not even partially.
- Page 15 Once the operation is complete, check the hose fittings for leaks using a soapy solution; never use a flame. The hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. To set it up for supply using other types of gas, see “3. ADAPTATION TO DIFFERENT TYPES OF GAS”.
-
Page 16: Adaptation To Different Types Of Gas
Before carrying out the following operations, disconnect the appliance from the power supply. The appliance is preset for natural gas G20 (2H) at a pressure of 20 mbar. In the case of operation with other types of gas, the burner nozzles must be changed and the minimum flame adjusted on the gas taps. - Page 17 Burner Natural gas – G20 20 mbar capacity (kW) Nozzle diameter Reduced capacity 1/100 mm Auxiliary (1) 1.05 Rapid (2) 2.50 Ultra-rapid (3) 3.90 1600 Arrangement of the burners on the cooking hob 1 Auxiliary 2 Rapid 3 Ultra-rapid...
-
Page 18: Final Operations
"7.1 Replacement of the cooking hob nozzles". After adjustment with a gas other than the preset one, replace the label on the casing of the appliance with the label corresponding to the new gas. This label can be obtained from the nearest Authorised Service Centre.