Advertisement
■ REPLACEMENT PARTS LIST
Notes:
1. Part numbers are indicated on most mechanical parts.
Please use this part number for parts orders.
2. A indicates that only parts specified by the manufacturer be used for safety.
3. SL-D2 (M) -► [M], SL-D2 (MC)
[MC]
Ref. No.
Part No.
Part Name & Description
|
INTEGRATED CIRCUIT
IC1
AN630U
Integrated Circuit
TRANSISTORS
Q1
2SC1846-R
Transistor
Q2
2SD637
Transistor
Q3
2SB641
Transistor
|
DIODES
D1
A
SVDSIRBA40
Rectifier
D2
A
SVDMI152
Rectifier
03.4,5
20A90
Diode
D6
MA161
Diode
07,9
SVDGD4205ALC
Light Emitting Diode
TRANSFORMER
T1
A
SLT41PU1D
Power Transformer
FUSE
|
FI (MC) only
A
XBA2F05NU100
500mA, Fuse
|
SWITCHES
|
SI
A
SFDSAH74403
Switch, Power
S2
EVAH27SBCAAY
Switch, Speed Selector
|
VARIABLE RESISTORS
|
VR1,2
EVLS6AAOOB54
50kfl (B), Speed Control (33 r.p.m. &
45 r.p.m.)
VR3
EVJ61AT12B24
20kfl (B), Pitch Control
_
RESISTORS
R 1
ERX1ANJ3R9
Metallic,
3.9fi,
1W,
± 5%
R2
ERD25FJ822
Carbon,
8.2kn,
1/4W,
± 5%
R3,4
ERD25FJ472
Carbon,
4.7kn,
1/4W,
± 5%
R5
ERD25FJ330
Ca.rbon,
330,
1/4W,
± 5%
Ref. No.
Part No.
Part Name & Description
R6
ERX1ANJ3R9
Metallic,
3.9kP,
1W,
± 5%
R7
ERO25CKF6202
Metal Film,
62kfl,
1/4W,
± 1%
R8
ERD25TJ393
Carbon,
39kfl,
1/4W,
± 5%
R9
ERD25TJ104
Carbon,
10Okfi,
1/4W,
± 5%
RIO
ERD25TJ563
Carbon,
56kfi,
1/4W,
± 5%
R11
ERD25FJ102
Carbon,
Ikfi,
1/4W,
± 5%
R12
ERO25CKF3902
Metal Film,
39k fl.
1/4W,
± 2%
R13
ERD25FJ103
Carbon,
iokn.
1/4W,
± 5%
R14
ERD25FJ331
Carbon,
330P,
1/4W,
± 5%
R15
ERD25TJ223
Carbon,
22kn,
1/4W,
± 5%
|
CAPACITORS
|
Cl
ECEB1HS471
Electrolytic,
470//F,
50V
C2
ECEA25Z4R7
Electrolytic,
4.7/iF,
25V
C3
ECEA50ZR22
Electrolytic,
0.22/iF,
50V
C4
ECQM1H104KS
Polyester,
0.1/iF,
50 V,
±10%
C5
ECEA50ZR33
Electrolytic,
0.33/iF,
50V
C6,7
ECEA50N1
Non-polar Electrolytic, 1/^F, 50V
C8
ECEA50N1
Non-polar Electrolytic, 1/iF, 50V
C9
A
ECQF2334KZ
Polypropylene ,0.33iiF,
200V,
±10%
CIO
ECQM1H154KZ
Polyester,
0.15/iF,
50V,
±10%
C11
ECQM1H104KS
Polyester,
0.1/iF,
50 V,
±10%
C12
ECEA25M10R
Electrolytic,
10/iF.
25V
C13
ECEA50M2R2R
Electrolytic,
2.2/iF,
50V
C14
ECEA50MR33R
Electrolytic,
0.33/iF,
50V
C15
ECEA1VS330
Electrolytic,
33/iF,
25V
C16
ECQM1H472KZ
Polyester,
0.0047/iF, 50 V,
±10%
C17
ECQM1H473KZ
Polyester,
0.0047/iF, 50 V,
±10%
C18, 19
ECEA50Z1
Electrolytic,
50V
C20
ECEA50Z1
Electrolytic,
¥F,
50V
C21
ECEA1AS221
Electrolytic,
220/iF,
6.3 V
C23
ECQM1H333KZ
Polyester,
0.0033/iF, 50 V,
± 10%
■ ADJUSTMENT PROCEDURE
Adjustment of Speed
(See Fig. 12)
If the number of revolutions cannot be correctly adjusted
by replacing 1C or other parts and turning the fine speed
adjusting knob (VR3), make the re-adjustment according to
the following procedure.
1. Set the fine speed adjusting knob to the central position.
2. In 33-1/3 r.p.m. mode, turn VR1 (33) so that the speed
is adjusted to the specified point by using a stroboscope.
3. Next, in 45 r.p.m. mode, turn VR2 (45) so that the
speed is adjusted to the specified point by using a strobo¬
scope.
4. After the adjustment, shift the speed change switch and
make sure that the speeds in 33-1/3 r.p.m. and 45 r.p.m.
modes are as specified.
Note:
For the above adjustments, follow the disassembly pro¬
cedure. Remove the bottom plate and put the set on a
table for repair work and gain access to it from
underneath.
8
It is also possible to adjust the set only with its tumtabld
removed.
Remove the turntable as illustrated below, then a hole will
be revealed from which a screwdriver can be inserted to
turn VR1 and VR2.
Advertisement
