Table of Contents
Advertisement
1 2 3 4 5 6
1 2 3 4 5 6
PROJECTION CONFIGURATION
1 2 3 4 5 6
1 2 3 4 5 6
1 2 3 4 5 6
1 2 3 4 5 6
1 2 3 4 5 6
Before Installation Change
The projector is electrically and mechanically set for 100 inch diagonal screen, front throw ceiling mount and a projection angle of
12.4˚ (XG75A)/12.2˚(XG135LC/XG110LC). If your application is different from the factory setting(for example, ceiling to floor
and screen size between 60 and 300 inch), you will have to reconfigure the projector for your application. Follow the change
procedures according to the instructions below.
For XG75A
To change screen size only:
1) Set the focus ring to the proper position.
For 100" screen size
For 120" screen size
R – A-3, B-3
R – A-3, B-3
G – A-1, B-3
G – A-1, B-3
B – A-3, B-3
B – A-3, B-3
2) Adjust the angle of the CRT's.
For 100" screen size
Move the CRT to the 100 position
To change to the desk top system (front)
1) Reverse the scan.
(See page 14.)
2) Set the focus ring to the proper position.
For 100" screen size
For 120" screen size
R – A-3, B-3
R – A-3, B-3
G – A-1, B-3
G – A-1, B-3
B – A-3, B-3
B – A-3, B-3
3) Adjust the angle of the CRT's.
For 100" screen size
Move the CRT to the 100 position
4) Select an installation from the PJ ORIENTATION menu in
the SETTING menu. (See "Projection Type Selection" in the
setup manual.)
(See pages15 and 16.)
For 180" screen size
R – A-5, B-5
G – A-1, B-5
B – A-5, B-5
(See page 16.)
For 120–180" screen size and the
other screen sizes
Move the CRT to the 120, 180, or
60–300 position
(See pages 15 and 16.)
For 180" screen size
R – A-5, B-5
G – A-1, B-5
B – A-5, B-5
(See page 16.)
For 120–180" screen size and the
other screen sizes
Move the CRT to the 120, 180, or
60–300 position
CHANGE.
To change to the ceiling mount system (rear)
1) Reverse the scan.
(See page 14.)
2) Set the focus ring to the proper position.
For 100" screen size
R – A-3, B-3
G – A-1, B-3
B – A-3, B-3
3) Adjust the angle of the CRT's.
For 100" screen size
Move the CRT to the 100 position
4) Select an installation from the PJ ORIENTATION menu in
the SETTING menu. (See "Projection Type Selection" in the
setup manual.)
To change to the desk top system (rear, 0 projection angle)
1) Set the focus ring to the proper position.
For 100" screen size
R – A-3, B-3
G – A-1, B-3
B – A-3, B-3
2) Adjust the angle of the CRT's
For 100" screen size
Move the CRT to the 100 position
3) Select an installation from the PJ ORIENTATION menu in
the SETTING menu. (See "Projection Type Selection" in the
setup manual.)
11
(See pages 16 and 17.)
For 120" screen size
For 180" screen size
R – A-3, B-3
R – A-5, B-5
G – A-1, B-3
G – A-1, B-5
B – A-3, B-3
B – A-5, B-5
(See page 17.)
For 120–180" screen size and the
other screen sizes
Move the CRT to the 120, 180, or
60–300 position
(See pages 16 and 17.)
For 120" screen size
For 180" screen size
R – A-3, B-3
R – A-5, B-5
G – A-1, B-3
G – A-1, B-5
B – A-3, B-3
B – A-5, B-5
(See page 17.)
For 120–180" screen size and the
other screen sizes
Move the CRT to the 120, 180, or
60–300 position
Advertisement
Table of Contents
