Shenzhen Digitech Co., Ltd. BN136 Manual Features Introduction Features & Parameter BN136 provides display functions about common riding data and statistical result, as well as partial practical features. Current speed Battery level Assists level Total range, trip range ...
Shenzhen Digitech Co., Ltd. BN136 Manual Operation Power on/off In power-off status, long press 【Power】to enter the logo interface and then the power-on interface displays after 1s. Release 【Power】button to enter riding menu. In power-on status, long press 【Power】to shut off.
Page 6
Shenzhen Digitech Co., Ltd. BN136 Manual Assist shifts Click on button【+】/【-】to shift gear. Long press 【-】button for 2s, the push assist mode of 6km/h starts. Light turns on/off Long press【+】for 2s to turn on light during riding. Clear trip range Long press 【Power】...
Page 7
Shenzhen Digitech Co., Ltd. BN136 Manual Note: In Bluetooth version, to clear trip range will clear max. speed, average speed, total Trip time, total calories. Alarm When E-bike system is alarming, it activates alarm code. Note: During alarming, press 【Power】to show the screen information, e.g. Trip range stays for 2s, keep flashing and alarm code displays.
Page 8
Shenzhen Digitech Co., Ltd. BN136 Manual Error Code (Meaning) (hexadecimal) Over current Error or MOS Damaged Throttle Hall Error Motor Phase Error Motor Hall Error Brake Error Under voltage Communication Error Lithium Battery No.2 Protocol Error Code Error Code (Meaning)
Page 9
Shenzhen Digitech Co., Ltd. BN136 Manual User Menu In a static and fault-free state, long press【+】and 【-】synchronously for 1s to enter the user menu. The speed limits, data unit, auto unit, auto power-off time backlight brightness can be set up.
Page 10
Shenzhen Digitech Co., Ltd. BN136 Manual 3、 Auto power-off time setting In the menu, figure is flashing to display current auto power-off time (in minute), click on 【+】 /【-】 to adjust, adjusting range 0-99, “0” means shut down auto power-off feature.
Page 11
Shenzhen Digitech Co., Ltd. BN136 Manual 6、 Bluetooth connection setting (Bluetooth only) In the menu, Bluetooth icon is flashing for 1s means Bluetooth disconnection. User can search and connect at APP, once operates successfully, the Bluetooth icon stops flashing and keeps lighting on.
Page 12
Shenzhen Digitech Co., Ltd. Shenzhen Digitech Co., Ltd. BN136 Manual The menu of power-on with password on with password If display has password, there If display has password, there’s password menu when power on. The p The password need be input after flashing for 1s.
Shenzhen Digitech Co., Ltd. Shenzhen Digitech Co., Ltd. BN136 Manual Advanced Menu BN136 provides advanced menu for E BN136 provides advanced menu for E-bike manufacturer, which could adjust E bike manufacturer, which could adjust E-bike configuration and the following parameters: configuration and the following parameters: ...
Page 14
Shenzhen Digitech Co., Ltd. BN136 Manual Speed Sensor In the menu, there’s “SnSr” at the right bottom, means SENSOR for short. The flickering data shows current setting speed sensor: Click on 【+】/【-】to adjust figure with range 1-12 and clicker on 【Power】to confirm and save, then switch to next Menu.
Page 15
Shenzhen Digitech Co., Ltd. BN136 Manual Click on 【+】/【-】 to switch battery voltage (in Volt) with range 36V/48V/52V. Click on 【Power】 to confirm and save, then switch to next menu. Power-on password setting In the menu, the power-on password can be set.
Page 16
Shenzhen Digitech Co., Ltd. BN136 Manual Attentions 1. Please make sure to turn off the power before the device is connected, otherwise it causes device damaged permanently; 2. ;Please make sure to fix the inner hexagon screws with torsion value 0.5Nm (maximum torsion value less than 0.6Nm), otherwise it causes device damaged;...