Related Manuals for Pedigo 5110 Series
Summary of Contents for Pedigo 5110 Series
- Page 1 5110 / 5110 Installation & Operation Manual 5110 Series Stretchers Part Number: 504-0056-00 10/13...
-
Page 2: Table Of Contents
Contents Owner’s Product Identification ..........2 Important Information . -
Page 3: Owner's Product Identification
Information that you will need to provide for servicing - key information is highlighted. Date of Purchase Serial Number Name of Owner / Facility / Department Weight Capacity Name of Authorized Pedigo Dealer Telephone # of Authorized Pedigo Dealer Address of Authorized Pedigo Dealer Lift fowler to find items 1 and 2. -
Page 4: Important Information
Safety Instructions The primary concern of Pedigo is that this equipment is operated and maintained with the safety of the patient and staff in mind. To assure safer and more reliable operation: of the purchaser. -
Page 5: Explanation Of Safety Symbols And Notes
Explanation of Safety Symbols and Notes Indicates a hazardous situation, that, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations. Indicates a hazardous situation, that, if not avoided, could result in death or serious injury. -
Page 6: Installation
Installation Unpacking The 5110-N stretcher weighs approximately 280 lbs (127 kgs) and the assistant if necessary and use proper lifting techniques . Failure to do so could result in serious back injury or other injury. To avoid damaging the stretcher’s upholstered top or other components, do not use a knife or other sharp object to open the stretcher’s packaging. - Page 7 out a concealed damage report. General items to inspect for shipping damage are: 1) Stretcher does not roll when the brakes are engaged. 2) Steering works properly - see page 11. 3) Trendelenburg and Fowler work properly. 4) Side rails work properly. 5) Mattress is not torn or damaged, etc.
-
Page 8: Description
Description Introduction The 5110-N and 5110-W General Purpose Stretcher is a fixed height stretcher which is primarily used to support and transport patients in any treatment or procedures environment, and may be used for general examinations and procedures. The table top is infinitely adjustable from a full horizontal table position to a full sitting position through the use of a pneumatic assist. -
Page 9: Components Overview
Components Overview The stretcher’s major components locations and names are shown below. Description of Components Mattress True Direction Steering Control Pedal Chassis Fowler Section (adjustable) Column... -
Page 10: Controls And Indicators
Controls and Indicators The illustrations below shows the location of the stretcher’s controls and indicators. The table below describes their function Function When squeezed, releases the Fowler pneumatic gas spring, allowing the Fowler (back) section to be raised or lowered. See “Fowler Section Positioning - Pneu- When squeezed, releases the Trendelenburg pneumatic gas spring, allowing Used to release the siderail so it may be lowered. -
Page 11: Checklist Of Installed Options & Authorized Accessories
Checklist: Installed Options & Authorized Accessories The options and accessories that are authorized for use with the stretcher are listed below . Check all the options and accessories installed or shipped with your stretcher. Option Name - Factory Install Required Narrow Item Number Wide Item Number 750203... -
Page 12: Stretcher Operation
Stretcher Operation True Direction Steering Controls There are two double-ended pedals located on each side of the stretcher. The function is indicated by the color of pedal. Pedal functions and positions are illustrated below: Engage steering by pressing down on the green pedal and then swiveling the caster at the patient’s right foot-end. - Page 13 Neutral is used to position the stretcher in a room, against a wall, or closer to a bed to transfer a patient. To engage Neutral, press down on the red pedal until the red and green pedals are level and an audible locking sound is heard.
-
Page 14: Fowler Section Positioning - Pneumatic Fowler
Fowler Section Positioning - Pneumatic Fowler The Fowler section (1) can be positioned at any angle between horizontal (0˚) and a full sitting position 1. Firmly grasp the end of the Fowler section (1), located on the head end of the stretcher, with both hands. -
Page 15: Fowler X-Ray Cassette Holder (Option)
Option To load an X-Ray cassette, do the following: section (2). Fowler section (2) and cassette holder (3) until it comes to rest against the support hinge (1). 3. Loosen cassette holder locking knob (4) by turning it counterclockwise. 4. Then, slide the cassette holder (3) up or down as necessary. 5. -
Page 16: Full Length X-Ray Litter (Option)
Option cassettes to be positioned under the patient. X-ray cassettes are inserted Adjusting the X-Ray cassette, do the following: as shown. 3. Loosen cassette holder locking knob (4) by turning it counterclockwise. 4. Then, slide the support hinge (1) up or down as necessary. 5. -
Page 17: Trendelenburg / Reverse Trendelenburg Positioning
Firmly grasp the litter top during positioning . Failure to do so could result in personal injury to the patient or the operator. Trendelenburg Positioning The litter top (1) can be positioned in the Trendelenburg position (head down) at any +12°... -
Page 18: Trendelenburg With Level Lock Option
Trendelenburg with Level Lock Option Firmly grasp the litter top during positioning . Failure to do so could result in personal injury to the patient or the operator. The level lock ensures the litter top is returned to horizontal position (0º) quickly and accurately: To position the litter top (1) in a Reverse Trendelenburg position: 1. -
Page 19: Side Rails
LIFT LOWER RAIL RELEASE 561-0380-00 To lower the side rail: 1. Grasp the side rail firmly with one hand and lift slightly. 2. Pull up on the side rail while engaging the release latch. 3. Gently lower the side rail. To raise the side rail: 1. -
Page 20: Oxygen Bottle Holder (Option)
Option Lower Oxygen Holder 1. Ensure the side rail is in its latched position. 2. Lower the O holder by pulling the “O Raise Oxygen Holder 3. Ensure the side rail is in its latched position. bottle holder near the center by cupping your hand underneath it. Push the O bottle of force, approximately the weight of a half-sack of flour. -
Page 21: Knee Flex / Leg Lift Options
Knee Flex / Leg Lift Options A stretcher equipped with the Knee Flex option can be placed in the Trauma, Leg Lift, and Knee Flex positions from the foot end of the stretcher. Hand Crank Option Trauma Position Using Hand Crank Page 22 Trauma Leg Lift Position Using Hand Crank... - Page 22 Option To place the litter top in the trauma position (from a flat bed), do the following: partially elevating the thigh section. The thigh section and the foot section should be angled approximately as shown in the illustration. position to prevent it from being damaged. To return the litter top to the flat position, do the following: rotated.
- Page 23 Option To place the litter top in the leg lift position (from a flat bed), do the following: should be positioned as shown in the illustration. position to prevent it from being damaged. To return the litter top to the flat position, do the following: rotated.
- Page 24 Option To place the litter top in the Knee Flex position (from a flat bed), do the following: The thigh section (6) and the foot section (3) should be positioned as shown in the illustration. position to prevent it from being damaged. To return the litter top to the flat position, do the following: rotated.
- Page 25 Option To place the litter top in the trauma position (from a flat bed), do the following: The thigh section and the foot section should be angled approximately as shown in the top illustration. push the pump handle back into the stowed position to prevent it from being damaged. To return the litter top to the flat position, do the following: grooves (5).
- Page 26 Option To place the litter top in the leg lift position (from a flat bed), do the following: should be positioned as shown in the illustration. push the pump handle back into the stowed position to prevent it from being damaged. To return the litter top to the flat position, do the following: grooves (5).
- Page 27 Option To place the litter top in the leg lift position (from a flat bed), do the following: section (3) should be positioned as shown in the illustration. the pump handle back into the stowed position to prevent it from being damaged. To return the litter top to the flat position, do the following: grooves (5).
-
Page 28: Locating Sockets For I.v. Poles / Accessory Pockets
end of the stretcher. (2) are located on each end of the stretcher. -
Page 29: Maintenance
Maintenance Cleaning Mattress Cover with a mild soap and water solution. The mattress cover material is resistant to most medicinal-type stains, but spilled on the upholstery immediately. Also, avoid the use of abrasive cleaners, steel wool, chlorinated bleaches, or solvents. Do not use high pressure water jets, submerge, or sterilize. -
Page 30: Preventive Maintenance
Soils or Stains: Use neutral soap suds and lukewarm water. Do not use harsh cleansers, solvents or detergents. Hard-To-Clean Spots: Use standard household/vinyl cleansers and a soft bristle brush on troublesome spots or stains. Pre-soak heavy, dried-on soil. Painted Metal Surfaces: Wipe all painted metal surfaces with a clean cloth at least once a week. Unpainted Metal Surfaces: Wipe all unpainted metal surfaces with a clean cloth. -
Page 31: Scheduled Maintenance
Scheduled Maintenance Inspection or Service Action* Moving parts Lubricate with lithium white grease or petroleum jelly, except linkages, which should be lubricated with Teflon or Silicon based lubricant. Caster pedal labels If labels are missing, replace as necessary. Warning & instruc tional Check for missing or illegible decals. -
Page 32: Calling For Service
Calling for Service If you are having a problem or have a question, refer to the inside front cover of this manual and call Technical Support at the number below. Make sure that you have the information that is highlighted on the inside front cover of this manual available. -
Page 33: Specifications
Specifications Model Number 5110 5110 Weight Capacity 500 lbs. (227 kg) 500 lbs. (227 kg) Overall Length 83" (211 cm) 83" (211 cm) 28" (71 cm) 28" (71 cm) 30" (76 cm) 30" (76 cm) Litter Positioning " (38 x 162 cm) 15"... -
Page 34: Limited Warranty
Pedigo’s obligation under this warranty is limited to the repair or replacement, at Pedigo’s option, of the parts or the products the defects of which are reported to Pedigo within the applicable warranty period and which, upon examination by Pedigo, prove to be defective. - Page 35 Installation & Operation Manual 5110 Series Stretchers © Pedigo Products, Inc. 2013 Printed in the U.S.A.