Table of Contents
Advertisement
1. SAFETY and GENERAL INFORMATION
Save these instructions. For your safety, read and understand the information contained within. The owner and opera-
tor shall have an understanding of this product and safe operating procedures before attempting to use this product.
Instructions and safety information shall be conveyed in the operator's native language before use of this product is
authorized. Make certain that the operator thoroughly understands the inherent dangers associated with the use and
misuse of the product. If any doubt exists as to the safe and proper use of this product as outlined in this factory autho-
rized manual, remove from service immediately. Inspect product before each use. It is recommended that, prior to each
use, an inspection is done by qualified personnel and that any missing or damaged parts, decals, warning / safety labels
or signs have to be replaced with factory authorized replacement parts only. Labels and instruction manuals are available
from the manufacturer.
Inspect before each use. Do not use if leaking, broken, bent, cracked or otherwise damaged parts are noted. If the
press has been or suspected to have been subjected to a shock load (a load dropped suddenly, unexpectedly upon it),
discontinue use until it is checked out by a BVA Hydraulics authorized service center. Owners and operators of this
equipment shall be aware that the use and subsequent repair of this equipment may require special training and
knowledge. It is recommended that an annual inspection is done by qualified personnel and that any missing or damaged
parts, decals, warning/safety labels or signs are replaced with BVA Hydraulics authorized replacement parts ONLY. Any
cylinder/pump/press that appears to be damaged in any way, is worn or operates abnormally shall be removed from
service immediately until such time as repairs can be made.
1.A
Use qualified personnel to maintain the press in good condition. Keep it clean for the best and safest performance.
1.B
Maximum load (61154 : 15 Ton, 61204 : 20 Ton, 61304 : 30 Ton, 61504 : 50 Ton). DO NOT exceed this rated capac-
ity.
1.C
Never apply excessive force to a workpiece, always use the pressure gauge to accurately determine the applied
load.
1.D
Use this press for the purpose for which it is intended. DO NOT use it for any other purpose it is not designed to
perform.
1.E
Keep children and unauthorized persons away from the work area.
1.F
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewelry, and tie long hair.
1.G
Wear CE approved impact safety goggles, full-face impact safety shield and heavy-duty work gloves when operat-
ing the press.
1.H
Keep proper balance and footing, do not overreach and wear nonslip footwear.
1.I
Only use this press on a surface that is stable, level, dry and not slippery, and capable of sustaining the load. Keep
the surface clean, tidy and free from unrelated materials and ensure that there is adequate lighting.
1.J
Inspect the press before each use. DO NOT use if bent, broken, cracked, leaking or otherwise damaged parts are
noted or when it has been subjected to a shock load.
1.K
Check to ensure that all applicable bolts and nuts are firmly tightened.
1.L
Ensure that the workpiece is center-loaded and secure. Keep hands and feet away from the bed area at all times.
1.M
DO NOT use the shop press to compress spring or any other item that could disengage and cause a potential
hazard. Never stand directly in front of loaded press and never leave a loaded press unattended.
1.N
DO NOT operate the press when you are tired or under the influence of alcohol, drugs or any intoxicating medica-
tion.
DO NOT allow untrained persons to operate the press.
1.O
1.P
DO NOT make any modifications to the press.
1.Q
DO NOT use brake fluid or any other improper fluid and avoid mixing different types of oil when adding hydraulic
oil. Only a good quality hydraulic jack oil can be used.
1.R
DO NOT expose the press to rain or any other kind of bad weather.
1.S
If the press needs repairing and/or there are any parts that need to be replaced, have it repaired by authorized
technicians and only use the replacement parts supplied by the manufacturer.
1.T
WARNING : the warnings, cautions and instructions discussed in this instruction manual cannot cover all possible
conditions and situations that may occur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by the operator.
2. SPECIFICATIONS
Model
Capacity
(Ton)
61154
61204
61304
61504
Stroke
(mm)
15
160
20
185
30
150
50
200
Working Range
Bed Width
(mm)
141 - 1185
138.5 - 1128.5
151 - 1031
69 - 1048
2
Side Stroke
(mm)
(mm)
500
169
510
179
535
200
730
245
Advertisement
Table of Contents
