Download Print this page

Global Industrial 761244 User Manual

Bi-level wall mounted filtered water cooler

Advertisement

Quick Links

User's manual
Customer Service
US: 1-800-645-2986
Bi-Level Wall Mounted Filtered Water Cooler
761244 is certified by
IAPMO
R&T against
NSF/ANSI/ 372
WARNING
• Keep compressor in upright position for 24 hours
before water connections and initial power-on. Failure
to do so will void warranty.
• For indoor commercial use only.
• All installation work must be performed by authorized
service personnel.
• Two or more people are recommended to lift and install
the unit.
• To avoid the risk of property damage and/or personal
injury, mount the unit to a flat finished wall surface with
adequate support.
• Check local codes for plumbing requirements prior to
installation.
• Prior to initial installation, install a shut-off valve(not
included) from the water supply.
• Thoroughly flush all water lines and fittings of all foreign
mater before connecting to the cooler. Failure to do so
will void warranty.
• Check for any leaks before initial operation
• DO NOT attempt to repair or replace any part of your
appliance unless it is specifically recommended in this
manual. All other services should be referred to a
qualified technician.
Manual del usuario
Servicio de atención al Cliente
US: 1-800-645-2986
• For use with clean, clear potable drinking water only.
• Shut-off water supply during installation to reduce risk
of water damage.
• Ensure proper ventilation by allowing appropriate
clearance of housing louvers to the wall on each side of
the cooler, as specified in rough-in guide.
• NEVER wire the compressor directly to an electrical
supply.
• DO NOT allow children to play with the appliance.
• Interior of unit may contain sharp edges. Wear gloves
when handling or servicing unit.
• Failure to follow installation instructions will void
warranty.
Note: These are intended for indoor commercial use
only. Do not expose to freezing temperatures. The
grounding of electrical equipment to water lines is a
common procedure. This grounding may be in the
building or occur away from the building. This
grounding can cause electric feedback into the water
cooler creating an electrolysis which creates a metallic
taste or
causes the water metal content to increase. Connect to
water supply using non-conductive materials.
1
TM
Manuel de l'utilisateur
Service à la clientèle
Canada: 888-645-2986
Model 761244
Read this manual thoroughly prior to
installation, operation or maintenance.
Keep these instructions in a safe location
for future reference. For questions, visit
globalindustrial.com or contact Customer
Service at 1-800-645-2982.
TM
122121

Advertisement

loading
Need help?

Need help?

Do you have a question about the 761244 and is the answer not in the manual?

Questions and answers

Summary of Contents for Global Industrial 761244

  • Page 1 Service à la clientèle US: 1-800-645-2986 US: 1-800-645-2986 Canada: 888-645-2986 Bi-Level Wall Mounted Filtered Water Cooler Model 761244 761244 is certified by IAPMO R&T against NSF/ANSI/ 372 Read this manual thoroughly prior to installation, operation or maintenance. Keep these instructions in a safe location for future reference.
  • Page 2 • Check local codes for electrical requirements. so will void warranty. • DO NOT disassemble or modify unit. • Required Tools: • Use Global Industrial filter only - Model 761215 or • 1.Safety Glasses 761215PF • 2.Safety Gloves • 3.Electric Drill...
  • Page 5 Assembly Instructions Bi-Level Wall Mounted Filtered Water Cooler Model 761244 BOX 2 CONTENTS Box 1 CONTENTS Ref. Qty. Description Ref. Qty. Description Secondary Fountain System Cooling System Mounting Bracket Lower Cover Mounting Bracket Cane Skirt Stainless Steel Pan Elbow Connector Insert...
  • Page 6 Assembly Instructions Bi-Level Wall Mounted Filtered Water Cooler Station, Filtered Remove mounting bracket Using a Phillips head screwdriver, remove the Mounting Bracket from the rear of the Cooling System by removing (1) screw. Set bracket aside for reinstallation. Discard after removal Bubbler Disconnect Current Water Line Connectors...
  • Page 7 Bi-Level Wall Mounted Filtered Water Cooler WARNING Assembly and installation of equipment should be performed by 2 people. Connect Water Lines • Connect water line (#1) from the Stainless Steel Pan to the Water Control Valve (#1) in the Cooling System. Push line until locked into place.
  • Page 8 Bi-Level Wall Mounted Filtered Water Cooler CAUTION Avoid crossing wires against sharp edges • Feed the Aviation Plug #19 through the Cooling System's frame and carefully lower the Stainless Steel Pan on top of the Cooling System. • Attach the Stainless Steel Pan to the Cooling System using (2) H4 screws.
  • Page 9 b82045fc-0b136962-90871f19-f891407c Assembly Instructions Bi-Level Refrigerated Bottle Filling Station, Filtered Install filter head bracket to Secondary Unit Using a Phillips head screwdriver, install the filter head bracket onto the frame of the Secondary Unit using the(4) screws previously removed. Connect #17 Water Line Connect the 39’...
  • Page 10 b82045fc-0b136962-90871f19-f891407c Assembly Instructions Bi-Level Refrigerated Bottle Filling Station, Filtered Always wear work gloves when lifting WARNING installation of equipment should be performed by 2 people. Lift Hanging assembled unit to wall Points Carefully hang assembled unit onto the wall by lowering onto mounting bracket.
  • Page 11 Bi-Level Wall Mounted Filtered Water Cooler Hanging assembled unit to wall • Carefully hang assembled bottle filler onto the wall by lowering onto both top and bottom wall mount brackets. CAUTION Onceassembled, d o not lift unit by BottleFiller Top Assembly .Use two people when lifting. Always wear work gloves when lifting •...
  • Page 12 Bi-Level Wall Mounted Filtered Water Cooler Remove the filter access door on the Lower Cover using the provided key. Set door aside Reattach lower cover • Reattach the Lower Cover to the Cooling System using (4) H1 anti-theft screws. • Fasten the Lower Cover to the bottom of the Stainless Steel Pan using (2) H1 anti-theft screws.
  • Page 13 Bi-Level Wall Mounted Filtered Water Cooler Connect Water Lines • Connect the 1/4 water line (#17) from the filter head in the Secondary Unit, to the Cooling Tank in the Bottle Filler unit. • Connect 1/4 water line (#17) from the Water Control Valve (#18) in the Bottle Filler unit, to the Solenoid Valve in the Secondary Unit.
  • Page 14 Bi-Level Wall Mounted Filtered Water Cooler Attach Cane Skirt Attach Decoration strips •Attach Cane Skirt to the • Attach Decoration strips to the undersideof the Stainless Steel underside of the Stainless Steel Pan using (6)H1 anit-theft screws. •Attach filter door of secondary Pan of secondary unit after they unit to higher unit.
  • Page 15 Bi-Level Wall Mounted Filtered Water Cooler Attach Lower Cover to Secondary Unit • Attach the Lower Cover (with the notch-out) to the Secondary Unit using (6) H1 anti-theft screws. WARNING: Make sure all electrical and water lines are tucked before attaching Lower Cover.
  • Page 16 User's Manual Bi-Level Wall Mounted Filtered Water Cooler Operation Note: Initial water flow may have sputter due to air in the water lines; this will be eliminated once air is purged from all water lines. To operate drinking fountain, push front or side activation buttons on the stainless steel pan to dispense cooled-filtered water from the bubbler.
  • Page 17 0b136962-90871f19-f891407c User's Manual Bi-Level Wall Mounted Filtered Water Cooler Programming Settings Accessing the programming Buttons: To access the programming buttons, open the filter access door on the lower cover using the provided key (H6). The two program buttons are located on the top of the access door frame.
  • Page 18 User's Manual Bi-Level Wall Mounted Filtered Water Cooler When filter level is at 100% 5 LED bars will be displayed When filter level is at 80% LED bars will be displayed When filter level is at 60% 3 LED bars will be displayed When filter level is at 40% 2 LED bars will be displayed When filter level is at 20%...