Table of Contents
Advertisement
Quick Links
VIGO INDUSTRIES INSTALLATION GUIDE FOR
SHOWER ENCLOSURE (MODEL VG06072)
!
SAFETY PRECAUTIONS
This Installation Guide uses the following symbols to indicate important information.
Always observe the instructions indicated by these symbols.
!
WARNING
Instructions that, if ignored, could result in death or serious personal injury caused by
incorrect handling or installation of the product. These instructions must be observed for
safe installation.
IMPORTANT
Maintenance and other important non-personal injury and non-material damage instructions
or statements that should be observed.
It is highly advised to dry fit the unit prior to any installation.
*VIGO reserves the right to modify/update all hardware and glass components based on
bettering the product for the end user's experience. If you have any questions contact VIGO
Tech Support at 1-866-591-7792.
1
Advertisement
Table of Contents
Related Manuals for VIGO VG06072
Summary of Contents for VIGO VG06072
- Page 1 It is highly advised to dry fit the unit prior to any installation. *VIGO reserves the right to modify/update all hardware and glass components based on bettering the product for the end user's experience. If you have any questions contact VIGO Tech Support at 1-866-591-7792.
- Page 2 MODEL VG06072 SOHO INSTALLATION INSTRUCTIONS FOR SHOWER DOOR PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Parts List 1. Door (1pc) 2. Hinge (2pc) 3. Split wall side seal strip (1pc) 4. Door bottom seal strip (1pc + 1pc is extra) 5. Handle assembly (1pc) 6.
- Page 3 26 1/4" X 70" 30X70 30" - 30 1/2" 70 5/8" 28 1/4" X 70" Product lines may change, contact your Vigo representative at 1-866-591-7792 or visit our website at www.vigoindustries.com for the most up to date product line information. MODEL VG06072...
-
Page 4: Before Starting
Compare items on your invoice with what you have received. Carefully review the Parts List on page 2. If any items are missing contact Vigo Industries at 1-866-591-7792. Please check our website at www.vigoindustries.com for additional information or instructional videos. - Page 5 If there is insufficient support, then reinforce the shower walls with wooden studs prior to shower door installation. [SEE FIG.1B] STUD FIG.1B CAUTION GASKETS NEED TO BE IN BETWEEN ALL GLASS AND METAL CONTACT. FAILURE TO DO SO CAN LEAD TO BREAKAGE AND POTENTIAL BODILY HARM. MODEL VG06072...
-
Page 6: Installation Steps
There is a 1/2" adjustment in the glass holes where the hinges are THIN GASKETS installed. You may need to adjust your hinges more than once to close your unit PLATE opening properly. HEX SCREWS VIEW FROM INSIDE OF THE CABIN MODEL VG06072... -
Page 7: Installing The Door
TWO OR MORE PEOPLE TO ASSIST Place the door (#1) on the shims raising the door up 7/16" to accommodate the bottom door seal strip. 7/16" SHIM (NOT PROVIDED) Align the door correctly using a level. LEVEL 7/16" SHIM (NOT PROVIDED) MODEL VG06072... - Page 8 Remove the door and drill holes into the wall where marked. Place plastic anchors (#8) inside the holes. Not necessary if installing into studs. Studs are the preferred means of installation, anchors can pull out of the wall causing property damage and bodily harm. MODEL VG06072...
- Page 9 1 5/8" screws (#7). One installer will need to hold the door in place while the other installer screws the hinges to the wall. Make sure not to rest the bottom door seal strip on the curb. OPEN POSITION MODEL VG06072...
- Page 10 NOTE: If the seal strips are not flat, use a hair dryer to apply minimal heat and press the seal strip back into position. FLOOR FLOOR MAGNETIC SEAL STRIP SHOULD SIT 1/16" OFF OF THE FLOOR AT THE FINAL INSTALLATION MODEL VG06072...
- Page 11 SHOULD BE 1/16" FROM THE BOTTOM Attach the door magnetic seal strips (#10) to each other and then close the door, making sure the door is on a level plain, keeping the LEVEL HOW MAGNETIC SEAL STRIPS SHOULD MEET MODEL VG06072...
- Page 12 THE FLOOR Remove the magnetic seal strip (#10) from the vertical track (#6). Hold the vertical track up to the wall where you previously marked and mark the wall through the holes in the vertical track (#6) for installation. MODEL VG06072...
- Page 13 Drill the vertical track (#6) to the wall with the 1 1/4" phillips screws (#9), making sure it is level and true. LEVEL MODEL VG06072...
-
Page 14: Handle Installation
(#5). Place the handle to the position on the door. Place plastic DOOR washers (supplied) on each side of the door. PANEL (1) Tighten the handle nuts from inside the shower. HANDLE ASSEMBLY GASKET HANDLE ASSEMBLY (5) MODEL VG06072... -
Page 15: Installing Covers
INSTALLING COVERS Install screw covers (#12) to the hinges. VIEW FROM INSIDE OF THE CABIN MODEL VG06072... - Page 16 In order to keep your shower enclosure in optimal working condition, Vigo recommends regularly inspecting your enclosure and tightening any hardware that may have loosened during use. This simple step will insure optimal results from your Vigo shower enclosure for many years to come.
- Page 17 Subject to the Warranty Service provision below, any product reported to the authorized dealer or to VIGO as being defective within the warranty period will be repaired or replaced (with a product of equal value) at the option of VIGO. This warranty extends to the original owner or end-user and is not transferable to a subsequent owner.
Need help?
Do you have a question about the VG06072 and is the answer not in the manual?
Questions and answers