Table of Contents
Advertisement
Quick Links
VIGO INDUSTRIES INSTALLATION GUIDE FOR
SHOWER ENCLOSURE (MODEL VG6073)
!
SAFETY PRECAUTIONS
This Installation Guide uses the following symbols to indicate important information.
Always observe the instructions indicated by these symbols.
!
WARNING
Instructions that, if ignored, could result in death or serious personal injury caused by
incorrect handling or installation of the product. These instructions must be observed for
safe installation.
IMPORTANT
Maintenance and other important non-personal injury and non-material damage instructions
or statements that should be observed.
It is highly advised to dry fit the unit prior to any installation.
*VIGO reserves the right to modify/update all hardware and glass components based on
bettering the product for the end user's experience. If you have any questions contact VIGO
Tech Support at 1-866-591-7792.
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VIGO TEMPO VG6073 Series
Summary of Contents for VIGO TEMPO VG6073 Series
- Page 1 It is highly advised to dry fit the unit prior to any installation. *VIGO reserves the right to modify/update all hardware and glass components based on bettering the product for the end user's experience. If you have any questions contact VIGO Tech Support at 1-866-591-7792.
- Page 2 MODEL VG6073 TEMPO INSTALLATION INSTRUCTIONS FOR SHOWER DOOR PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Parts List 1. Door (1pc) 2. Hinge (2pc) 3. Split wall side seal strip (1pc) 4. Door bottom seal strip (1pc + 1pc is extra) 5. Handle assembly (1pc) 6.
- Page 3 26 1/4" X 70" 30X70 30" - 30 1/2" 70 5/8" 28 1/4" X 70" Product lines may change, contact your Vigo representative at 1-866-591-7792 or visit our website at www.vigoindustries.com for the most up to date product line information. MODEL VG6073...
-
Page 4: Before Starting
Compare items on your invoice with what you have received. Carefully review the Parts List on page 2. If any items are missing contact Vigo Industries at 1-866-591-7792. Please check our website at www.vigoindustries.com for additional information or instructional videos. - Page 5 PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION Remove the plastic layer from the base border (if needed). Do NOT remove the plastic layer off the plastic platform of the base/tub. Properly apply silicone to the wall and base joints. Measure your opening to determine if your unit will fit properly. See the chart below to determine the dimensions.
-
Page 6: Installation Steps
INSTALLATION STEPS INSTALLING THE SPLIT WALL SIDE SEAL STRIP Clean all glass panel edges receiving seal strips with rubbing alcohol. Cut and install the seal strip (#3) according to the seal strip LONGER FLANGE diagram, making sure that the longer of the SHOULD BE ON THE flanges is on the inside of the shower. -
Page 7: Installing The Door
INSTALLING THE DOOR WARNING DOOR PANEL INSTALLATION REQUIRES TWO OR MORE PEOPLE TO ASSIST Place the door (#1) on the shims raising the door up 7/16" to accommodate the bottom door seal strip. 7/16" SHIM (NOT PROVIDED) Align the door correctly using a level. LEVEL 7/16"... - Page 8 Hold the door in the open position and mark two (2) holes on the wall for the mounting screws for each hinge. OPEN POSITION 7/16" SHIM (NOT PROVIDED) Remove the door and drill holes into the wall where marked. Place plastic anchors (#8) inside the holes.
- Page 9 Clean the door glass panel (#1) edges where the door bottom seal strip (#4) is to be installed with rubbing alcohol. The door bottom seal strip (#4) will have to be fit and cut to the proper size. Verify that the lip of the seal strip faces toward the inside of the shower cabin before seal strip installation.
- Page 10 INSTALLING THE MAGNETIC SIDE SEAL STRIP Clean all glass panel edges receiving seal strips with rubbing alcohol. Install the seal strip (#10) according to seal strip diagram. VIEW FROM THE OUTSIDE The seal strip should rest 1/16" off of the "B"...
- Page 11 VERTICAL TRACK INSTALLATION Install the door magnetic seal strip (#10) to the vertical track (#6) leaving a 1/16" gap at the bottom. [SEE FIG.6] The vertical track (#6) and the door magnetic seal strip (#10) are the same length. MAGNETIC SEAL STRIP SHOULD BE 1/16"...
- Page 12 Mark the wall on both sides of the vertical track (#6). The vertical track should be installed with the bottom resting on the floor LEVEL VERTICAL TRACK SHOULD REST ON THE FLOOR Remove the magnetic seal strip (#10) from the vertical track (#6). Hold the vertical track up to the wall where you previously marked and mark the wall through the holes in the vertical track (#6) for installation.
- Page 13 Remove the vertical track, pre-drill and sink plastic anchors (#11) into the wall. necessary if installing into studs. Studs are the preferred means of installation, anchors can pull out of the wall causing property damage and bodily harm. Drill the vertical track (#6) to the wall with the 1 1/4"...
-
Page 14: Handle Installation
Install the magnetic seal strip (#10) back onto the vertical track (#6), making sure that it complements the door magnetic seal strip. HOW MAGNETIC SEAL STRIPS SHOULD MEET HANDLE INSTALLATION Assemble the door handles (#5) to the door (#1). Place the handle with the threaded pin (#5-1) through the hole in the door (#1). -
Page 15: Installing Covers
INSTALLING COVERS Install screw covers (#12) to the hinges. VIEW FROM INSIDE OF THE CABIN MODEL VG6073... - Page 16 In order to keep your shower enclosure in optimal working condition, Vigo recommends regularly inspecting your enclosure and tightening any hardware that may have loosened during use. This simple step will insure optimal results from your Vigo shower enclosure for many years to come.
- Page 17 Subject to the Warranty Service provision below, any product reported to the authorized dealer or to VIGO as being defective within the warranty period will be repaired or replaced (with a product of equal value) at the option of VIGO. This warranty extends to the original owner or end-user and is not transferable to a subsequent owner.
Need help?
Do you have a question about the TEMPO VG6073 Series and is the answer not in the manual?
Questions and answers