Related Manuals for System Q CCT269
Summary of Contents for System Q CCT269
- Page 1 Doc XCCT269 CCT269 COLOUR Quad Processor Instructions System Q Ltd. E-mail support@systemq.com or fax support 01246 222888...
-
Page 2: Table Of Contents
2005-01-17 version 1.1 The author assumes no responsibility for any errors or omissions, which may appear in this document, nor does he make a commitment to update the information contained herein. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 3: Contents
Doc XCCT269 CCT269 COLOUR Quad Processor Instructions System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 4: Introduction And Features
Supports an alarm– triggered relay output RELAY OUT that can control other security systems, related electric devices or to start VCR recording. q 40 alarm record and list occurrences. q Low power consumption saves up to 50% in power costs. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 5: Installation
It is applied to control other equipments, Input Terminal when an alarm has been triggered. MONITOR Video signal This terminal represents the video signal output for output BNC type connecting to external Monitors. Terminal System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 6: Illustrate Of Installation Procedures
Step 1: Figure below shows Illustrations of the external video Cameras, Monitor and VCR: RELAY OUT VIDEO OUT VIDEO IN POWER IN COM/NO/NC MONITOR QUAD DC 12V Master Camera 1 Monitor Camera 2 Camera 3 Camera 4 System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... - Page 7 L A Y “ External Start Record” connector on the VCR i Attention The max current and voltage type are DC24V-2Amp or AC120V-1Amp for RELAY OUT. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888...
- Page 8 .Insert the (— ) type screwdriver into the orange color release button (on the top of the terminal connectors). . And then push upward. . Pull terminal wires out. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888...
-
Page 9: Operating Instructions
2Í2 image of field. „ display. CH2 image. CH2 Full quadrant 2. quadrant 2. display. 3 LED light or 3 LED light 3 LED light 3 LED light 3 LED light dark System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 10: Operating Instructions
After POWER ON and the cameras have been connected, but any sudden disconnection after POWER On will automatically trigger the alarm, and the "LOSS" message will be shown on the monitor. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 11: Sequence Mode
"VCR PLAY" message will be shown on the monitor. In the VCR PLAYBACK MODE, the VCR OUT will change to mute (blue background) & stop to detect for the CH1~4 video loss until leave this mode! System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 12: System Setup
DATE FORMAT: YY.MM.DD DATE: 2003.08.27 TIME: 12:35:50 LOCATION:BOTTOM MONITOR DATE\TIME: VCR OUT DATE\TIME: ON -- SEQUENTIAL SETTING —- SEQUENCE: Q 1 2 3 4 . . . DWELL TIME: Figure 1. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... - Page 13 SEQUENCE There are eight positions to select and setup the random switching sequence. Where QUAD display; 1 CH1 Full display; 2 CH2 Full display; 3 CH3 Full display; 4 CH4 Full display; Skip. iNOTICE System Q Ltd. E-mail support@systemq.com or fax support 01246 222888...
-
Page 14: Display Setup
HUE: The camera 1~4 (channel 1~4) image HUE (color saturation) adjustable by user. The HUE range: 0~99. 3.2.4.4 TITLE SETUP..TITLE SETUP ..CH1: CAMERA01 CH2: ON CAMERA02 CH3: ON CAMERA03 CH4: ON CAMERA04 CHARACTER COLOR: WHITE Figure 4. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 15: Motion Setup
When MD.NUM is set to "04" – to enable motion detection function there should be more than 4 motion detection windows. When MD.NUM is set to "15" – to enable motion detection function there should be more than motion detection windows. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 16: Pip\Pop Setup
VCR FREEZE HOLD TIME The processor will automatically release freeze image after the time period that was set elapses. (Time range 0~30 seconds.) If the VCR FREEZE HOLD TIME is set to 0, this function is unavailable. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 17: Load Default & Watch Alarm List
After the value is set, press the buttons one last time to finalize the set- up or to disengage. To leave this set-up menu, just press the NEXT PAGE key one last time. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... - Page 18 ‘ ’ will be displayed on LOAD FACTORY RESET) BORDER LINE WIDTH The border line width settings is adjustable by user.nOFFn4\2n8\4n BORDER LINE COLOR The On Screen Display borderline is adjustable by the user. nWHITEnGRAYnBLACKnBLUEnREDn MAGENTAnGREENnCYANnYELLOWn System Q Ltd. E-mail support@systemq.com or fax support 01246 222888...
-
Page 19: Warning
DC IN socket, please use the specified DC12V±5% 1.0A power adapter. Otherwise, it may cause system damage, and result in injury. 6. The maximum of timer inaccuracy difference for RELAY OUT TIMER & BUZZER ALARM TIME is one second. System Q Ltd. E-mail support@systemq.com or fax support 01246 222888... -
Page 20: Specifications
All specifications are approximate. System Q reserves the right to change any product specification or features without notice. Whilst every effort is made to ensure that these instructions are complete and accurate, System Q cannot be held responsible in any way for any losses, no matter how they arise, from errors or omissions in these instructions, or the performance or non-performance of the camera or other equipment that these instructions refer to.
Need help?
Do you have a question about the CCT269 and is the answer not in the manual?
Questions and answers