Amd 760g series amd 760g & amd sb750
based m/b for socket am3 (22 pages)
Summary of Contents for JETWAY 754GT7-SLI-G
Page 1
754GT7-SLI-G / 754GT7-SLI -P 754GT7-Ultra-G / 754GT7-STD-G 754GT7-STD-G / 754GT7-STD-P USER'S MANUAL M/B For 64-bit AMD Socket 754 Processor NO. G03754GT7SLIR110 Rev:1.0 Release date: Sep 2005 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are...
Revision History Date First Edition Sep 2005 Item Checklist 754GT7-SLI-G / 754GT7-SLI-P / 754GT7-Ultra-G / 754GT7-Ultra-P / 754GT7-STD-G / 754GT7-STD-P motherboard Cable for IDE/Floppy CD for motherboard utilities SLI Supported Bridge (For 754GT7-SLI-G / 754GT7-SLI-P motherboard only) Cable for serial ATA IDE port SPDIF-IN/SPDIF-OUT Adaptor(optional) 754GT7 Motherboard Series User’s Manual...
Introduction of 754GT7 Motherboard 1-1 Features of motherboard The 754GT7-SLI-G / 754GT7-SLI-P / 754GT7-Ultra-G / 754GT7-Ultra-P / 754GT7-STD-G / 754GT7-STD-P motherboard is based on NVIDIA nForce4-SLI, nForce4-Ultra, and nForce4 single chip technology which supports the innovative 64-bit AMD Athlon64 and Sempron processors with HyperTransport Technology.
Some special features---CPU Thermal Throttling/ CPU Vcore 7-shift/ CPU Smart Fan/ Debug Port(Option) in this motherboard are designed for power user to use the over-clocking function in more flexible ways. But please be caution that the over-clocking maybe cause the fails in system reliabilities.
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU:...
Chapter 2 Hardware Installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6.
(2) Keyboard function Enabled/Disabled: JP1 1-2 Closed KB/USB Power ON Disable (Default) 2-3 Closed KB/USB Power ON Enabled Keyboard/Mouse & USB Power On Setting (3) USB Power On function Enabled/Disabled: JP2 1-2 closed USB Power On Disable 2-3 closed USB Power On Enabled (Default) USB Power-On Setting 2-3 Install CPU...
establish the relationship between the various components. Driver - software, which defines the characteristics of a device for use by another device or other software. Processor - the "central processing unit" (CPU); the principal integrated circuit used for doing the "computing" in "personal computer" Front Side Bus Frequency - the working frequency of the motherboard, which is generated by the clock generator for CPU, DRAM and PCI BUS.
2-3-3 About AMD Athlon64 CPU Installation Step by Step Pulling the level sideways away from the Insert the CPU with the correct orientation as socket then upward to a 90-degree angle. shown Above. The notched corner should point toward the end of the level. Zero Insertion Force needed while the CPU Pulling the level sideways back to the socket.
2-4 Install Memory This motherboard provides three 184-pin DDR DUAL INLINE MEMORY MODULES (DIMM) sockets for DDR memory expansion available from minimum memory volume of 128MB to maximum memory volume of 3.0GB DDR SDRAM. Valid Memory Configurations Bank 184-Pin DIMM Total Memory Bank 0, 1 (DIMM1) DDRDDR266/DDR333/DDR400...
2-5 Expansion Cards WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers.
IMPORTANT! If using PCI cards on shared slots, make sure that the drivers support “Shared IRQ” or that the cards don’t need IRQ assignments. Conflicts will arise between the two PCI groups that will make the system unstable or cards inoperable. 2-5-4 PCI Express Slot This motherboard provides three 16-lane PCI Express slot intended for Graphics Attach(Two symmetrical PCI-Express x16 graphics slots in different color with other slots deliver up to...
2-5-5 SLI Bridge for NVIDIA SLI Tech. Supported VGA Cards In order to activate the NVIDIA SLI technology, you have to install the embedded SLI Bridge for your NVIDIA SLI Tech. Supported VGA Cards before you activating the advance multi- GPUs functions.
2-6 Connectors, Headers 2-6-1 Connectors (1) Power Connector (24-pin block) : ATXPWR24P ATX Power Supply connector. This is a new defined 24-pins connector that usually comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard.
Page 19
This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 12V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system.
Page 20
Optional Gigabit LAN PS/2 Surrback Mouse PRINTER Line-IN CEN/LFE Line-OUT MIC-IN Surround PS/2 COM1 USB1 COM2 Keyboard (9) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. Pin 1 Floppy Drive Connector (10) Primary IDE Connector (40-pin block): IDE1...
Page 21
This connector connects to the next set of Master and Slave hard disks. Follow the same procedure described for the primary IDE connector. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector.
2-6-2 Headers Line-Out/MIC Header for Front Panel (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable. Without install the cable, this header default setting is 5-6 short, 9-10 short. When you install the cable you have take off these jumpers. AUDIO Pin 1 Line-Out, MIC Headers...
Page 23
rebooting in order to prolong the lift of the system’s power supply. See the figure below. Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. PWRLED Pin 1 JW FP SPEAK Pin 1 Pin 1 System Case Connections...
Page 24
(9) CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. C DIN CD Audio-In Headers (10) In/Out Header: SPDIF (Module Optional) SPDIF Pin 1 SPDIF-Bracket Connector (11) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module.
2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used.
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system.When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.
3-3 The Main Menu Once you enter Award ® BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
Use this menu to specify your settings (frequency, Voltage) for overclocking demand Password Settings This entry for setting Supervisor password and User password Load Optimized Defaults Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use.
IDE Channel 0 Master / Channel 0 Slave / Channel 1 Master / Channel 1 Slave SATA Channel 1, 2, 3, 4 Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category.
Page 30
Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
Security Option This category allows you to limit access to the system and Setup, or just to Setup. System The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt. Setup (default) The system will boot, but access to Setup will be denied if the correct password is not entered prompt.
The default setting is “ ” for this selection, and it provides with the adjustable ↓16↑16 bandwidth selection for you to choose the combination of stream with x16 and x16 bandwidth of updoad and down between the processor and system chip. DRAM Timing Settings Please refer to section 3-6-1 System BIOS Cacheable...
3-7 Integrated Peripherals Phoenix – AwardBIOS CMOS Setup Utility Integrated Peripherals > OnChip IDE Function Press Enter Item Help > OnChip Device Function Press Enter > OnChip Super IO Function Press Enter Init Display First PCI Slot Menu Level > ↑↓→←...
OnChip IDE Channal0/Channel1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports.
Onboard AC97 Audio Device This item allows you to decide to enable/disable/auto the chipset family to support AC97 Audio. The settings are: Enabled, Disabled, Auto. Onboard LAN Device Setting to [Auto] allows the BIOS to auto-detect the LAN controller and enable it. Setting options:[Auto] and [Disabled] .
(3BC/IRQ7)/ Line Printer port 0 (278/IRQ5)/ Line Printer port 2 (378/IRQ7) Line Printer port 1 Parallel Port Mode : Standard Parallel Port : Enhanced Parallel Port : Extended Capability Port ECP+EPP :Extended Capability Port and Enhanced Parallel Port SPP/EPP/ECP/ECP+EPP To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.”...
Blank Screen This option only writes blanks to the video buffer. V/H SYNC+Blank This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer. Power Button Function Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The settings are: Delay 4 Sec, Instant-Off.
3-10-1 Smart FAN Configurations Phoenix – AwardBIOS CMOS Setup Utility Smart FAN Configurations CPUFAN Smart Mode Disabled Item Help CPU SmartFAN Full-Speed Temp CPU SmartFAN Idle Temp SFAN1 Smart Mode Disabled Menu Level > SFAN1 SmartFAN Full-Speed Temp SFAN1 SmartFAN Idle Temp SFAN2 Smart Mode Disabled SFAN2 SmartFAN Full-Speed Temp...
Page 40
Phoenix – AwardBIOS CMOS Setup Utility Thermal Throttling Options CPU Thermal-Throttling Disabled CPU Thermal-Throttling Temp Item Help CPU Thermal-Throttling Beep Enabled CPU Thermal-Throttling Temp CPU Thermal-Throttling Duty 50.00% Integral number: ↑↓:Move ENTER:Accept ESC:Abort CPU Thermal-Throttling Temp Menu Level > Min = Max = Key in a Integral number: ↑↓:Move ENTER:Accept ESC:Abort...
3-12 Power User Overclock Settings Phoenix – AwardBIOS CMOS Setup Utility Power User Overclock Settings PCIE Clock 100MHZ Item Help ** Current Host Frequency is 200MHZ ** CPU at Next Boot is 200MHZ *** Current DRAM Frequency is 200MHZ*** Menu Level > DRAM Clock at Next Boot is Auto CPU Ratio Select...
Page 42
Phoenix – AwardBIOS CMOS Setup Utility Power User Overclock Settings PCIE Clock Item Help CPU Vcore 7-Shift ** Current CPU Clock 200MHZ ** Normal .....[ CPU Clock at Next Boot is 50mv .....[ *** Current DRAM Clock 200MHZ *** Menu Level > + 100mv .....[ DRAM Clock at Next Boot...
3-13 Password Settings Phoenix – AwardBIOS CMOS Setup Utility Password Settings Item Help Set Supervisor Password Press Enter Set User Password Press Enter Menu Level > ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults You can set either supervisor or user password, or both of them.
Chapter 4 DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly.
Install nForce Integrated Driver nForce * nForce Integrated driver pack include following device driver: NVIDIA GART driver : If you are using an AGP VGA Card, please install NVIDIA AGP GART driver which provides service routines to your VGA driver and interface directly to the hardware for speedy graphic access.
Page 46
5. Please choose to install the NVIDIA firewall 6. If you want to install NVIDIA firewall and and Forceware Network Access Manager Forceware Network Access Manager utility Utility Driver for demanding on you own. 7. Select install complete software and Click 8.
4-4 PC-CILLIN Install PC-CILLIN 2005 Anti-virus program Click PC-CILLIN when MAGIC INSTALL Please select “Install program” when the MENU appears "Trend Micro internet security" installshield wizard windows appears Click NEXT and Enter your Customer Please select install “FULL” function or Information, Click NEXT or choose Change install “Antivirus software”...
STEP 2. Copy utility program to your boot disc. You may copy from DRIVER CD X:\FLASH\AWDFLASH.EXE or download from our web site. STEP 3. Download and make a copy of the latest BIOS for 754GT7-SLI-D/ 754GT7-SLI-G/ 754GT7-SLI-P motherboard series from the web site to your boot disc.
start the computer, type “Awdflash A:\754GT7xxx.BIN /SN/PY/CC/R” 754GT7xxx.BIN is the file name of latest BIOS it can be 754GT703.BIN or 754GT702.BIN means don’t save existing BIOS data means renew existing BIOS data means clear existing CMOS data means restart computer STEP 5.
Page 51
Step 3. Making RAID driver diskette before Install WindowsXP/2000 Before you install the Windows XP or Windows 2000, you will need to make a RAID driver diskette before you start to install the Operating System. How to make a RAID driver diskette? 1: Insert the diskette which is being formatted in floppy drive on a system which can start OS.
4-8 Pro Magic Plus Function Introduction What’s Pro Magic Plus? Tired with reinstall OS each time when it doesn’t work? Does your computer often crash down or unable to work after installed new software? Have you had great loses and troubles because of computer problems? Still using time-consuming backup software that occupies lots of HD space? Pro Magic Plus- an instant system recovery software tailored to solve these problems for...
Page 53
System Requirements ◇ First OS must be Windows 98 SE/ME/2000/XP ◇ Support Only Windows OS (No Linux) ◇ Windows server OS and Windows NT not supported ◇ Minimum of Intel 486 or above, 16MB of memory or above ◇ Minimum of 500MB free/usable space or above ◇...