Rockwell RC336D Command Reference Manual page 4

3. DATA COMMAND SET..................................................................................................................................................... 3-1
3.1 COMMAND GUIDELINES ...................................................................................................................................... 3-1
3.1.1 Escape Code Sequence ............................................................................................................................ 3-1
3.2 DATA COMMANDS ................................................................................................................................................ 3-1
3.2.1 Generic Modem Control ............................................................................................................................. 3-1
3.2.1.1
3.2.1.2
3.2.1.3
3.2.1.4
3.2.1.5
3.2.1.6
3.2.1.7
3.2.1.8
3.2.1.9
3.2.1.10 +GCAP - Request Complete Capabilities List............................................................................ 3-6
3.2.1.11 +GCI - Country of Installation..................................................................................................... 3-7
3.2.1.12 &F - Restore Factory Configuration (Profile).............................................................................. 3-8
3.2.1.13 &T - Local Analog Loopback Test.............................................................................................. 3-8
3.2.1.14 &Y - Designate a Default Reset Profile ...................................................................................... 3-8
3.2.1.15 &W - Store Current Configuration .............................................................................................. 3-9
3.2.1.16 &Zn=x - Store Telephone Number ............................................................................................. 3-9
3.2.1.17 %7 - Plug and Play Serial Number............................................................................................. 3-9
3.2.1.18 %8 - Plug and Play Vendor ID and Product Number ............................................................... 3-10
3.2.1.19 **- Load Flash Memory ............................................................................................................ 3-10
3.2.2 DTE-Modem Interface commands ........................................................................................................... 3-11
3.2.2.1
3.2.2.2
3.2.2.3
3.2.2.4
3.2.2.5
3.2.2.6
3.2.2.7
3.2.2.8
3.2.2.9
3.2.2.10 &Q - Sync/Async Mode ............................................................................................................ 3-19
3.2.2.11 &R - RTS/CTS Option .............................................................................................................. 3-19
3.2.2.12 &S - DSR Override................................................................................................................... 3-20
3.2.2.13 &X - Select Synchronous Clock Source................................................................................... 3-20
3.2.2.14 +IPR - Fixed DTE Rate ............................................................................................................ 3-21
3.2.2.15 +IFC - DTE-Modem Local Flow Control ................................................................................... 3-22
3.2.2.16 +ILRR - DTE-Modem Local Rate Reporting............................................................................. 3-22
3.2.3 Call Control .............................................................................................................................................. 3-23
3.2.3.1
3.2.3.2
3.2.3.3
3.2.3.4
3.2.3.5
3.2.3.6
3.2.3.7
3.2.3.8
3.2.3.9
3.2.3.10 &P - Select Pulse Dial Make/Break Ratio ................................................................................ 3-28
3.2.3.11 &V - Display Current Configuration and Stored Profiles .......................................................... 3-29
3.2.3.12 &V1 - Display Last Connection Statistics ................................................................................. 3-30
3.2.3.13 \V - Single Line Connect Message Enable............................................................................... 3-31
3.2.3.14 %L - Report Line Signal Level ................................................................................................. 3-31
3.2.3.15 %Q - Report Line Signal Quality .............................................................................................. 3-32
3.2.3.16 *B - Display Blacklisted Numbers............................................................................................. 3-32
iv
Command Reference Manual
Z - Soft Reset and Restore Profile ............................................................................................. 3-1
+FCLASS - Select Active Service Class .................................................................................... 3-2
+VCID - Caller ID (CID).............................................................................................................. 3-2
\N - Operating Mode................................................................................................................... 3-3
-SMS= - Select Mode ................................................................................................................. 3-4
I - Identification........................................................................................................................... 3-5
+GMI - Request Manufacturer Identification .............................................................................. 3-6
+GMM - Request Model Identification........................................................................................ 3-6
+GMR - Request Revision Identification .................................................................................... 3-6
E - Command Echo.................................................................................................................. 3-11
Q - Quiet Results Codes Control.............................................................................................. 3-12
V - Result Code Form .............................................................................................................. 3-12
W - Connect Message Control ................................................................................................. 3-12
X - Extended Result Codes...................................................................................................... 3-13
&C - RLSD (DCD) Option......................................................................................................... 3-17
&D - DTR Option ...................................................................................................................... 3-17
&K - Flow Control ..................................................................................................................... 3-18
&M - Asynchronous/Synchronous Mode Selection .................................................................. 3-18
D - Dial ..................................................................................................................................... 3-23
T - Set Tone Dial Default.......................................................................................................... 3-25
P - Set Pulse Dial Default......................................................................................................... 3-25
A - Answer................................................................................................................................ 3-25
H - Disconnect (Hang-Up)........................................................................................................ 3-25
O - Return to On-Line Data Mode ............................................................................................ 3-26
L - Speaker Volume ................................................................................................................. 3-26
M - Speaker Control ................................................................................................................. 3-26
&G - Select Guard Tone........................................................................................................... 3-28
1199